Lines Matching +full:preemphasis +full:- +full:width
1 // SPDX-License-Identifier: GPL-2.0
8 /dts-v1/;
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/input/linux-event-codes.h>
12 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
18 /delete-node/ &rmtfs_mem;
27 stdout-path = "serial0:115200n8";
30 gpio-keys {
31 compatible = "gpio-keys";
35 pinctrl-names = "default";
36 pinctrl-0 = <&volume_down_gpio &volume_up_gpio>;
38 vol-down {
42 debounce-interval = <15>;
45 vol-up {
49 debounce-interval = <15>;
53 reserved-memory {
59 no-map;
68 compatible = "qcom,rmtfs-mem";
70 no-map;
72 qcom,client-id = <1>;
76 no-map;
85 no-map;
92 record-size = <0x40000>;
93 console-size = <0x40000>;
94 ftrace-size = <0x40000>;
95 pmsg-size = <0x200000>;
96 devinfo-size = <0x1000>;
97 ecc-size = <16>;
101 vph_pwr: vph-pwr-regulator {
102 compatible = "regulator-fixed";
103 regulator-name = "vph_pwr";
104 regulator-min-microvolt = <3700000>;
105 regulator-max-microvolt = <3700000>;
110 * is always-on; model it as a fixed regulator.
112 vreg_s4a_1p8: pm8998-smps4 {
113 compatible = "regulator-fixed";
114 regulator-name = "vreg_s4a_1p8";
116 regulator-min-microvolt = <1800000>;
117 regulator-max-microvolt = <1800000>;
119 regulator-always-on;
120 regulator-boot-on;
122 vin-supply = <&vph_pwr>;
130 ts_1p8_supply: ts-1p8-regulator {
131 compatible = "regulator-fixed";
132 regulator-name = "ts_1p8_supply";
134 regulator-min-microvolt = <1800000>;
135 regulator-max-microvolt = <1800000>;
138 enable-active-high;
139 regulator-boot-on;
145 firmware-name = "qcom/sdm845/oneplus6/adsp.mbn";
149 pm8998-rpmh-regulators {
150 compatible = "qcom,pm8998-rpmh-regulators";
151 qcom,pmic-id = "a";
153 vdd-s1-supply = <&vph_pwr>;
154 vdd-s2-supply = <&vph_pwr>;
155 vdd-s3-supply = <&vph_pwr>;
156 vdd-s4-supply = <&vph_pwr>;
157 vdd-s5-supply = <&vph_pwr>;
158 vdd-s6-supply = <&vph_pwr>;
159 vdd-s7-supply = <&vph_pwr>;
160 vdd-s8-supply = <&vph_pwr>;
161 vdd-s9-supply = <&vph_pwr>;
162 vdd-s10-supply = <&vph_pwr>;
163 vdd-s11-supply = <&vph_pwr>;
164 vdd-s12-supply = <&vph_pwr>;
165 vdd-s13-supply = <&vph_pwr>;
166 vdd-l1-l27-supply = <&vreg_s7a_1p025>;
167 vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
168 vdd-l3-l11-supply = <&vreg_s7a_1p025>;
169 vdd-l4-l5-supply = <&vreg_s7a_1p025>;
170 vdd-l6-supply = <&vph_pwr>;
171 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
172 vdd-l9-supply = <&vreg_bob>;
173 vdd-l10-l23-l25-supply = <&vreg_bob>;
174 vdd-l13-l19-l21-supply = <&vreg_bob>;
175 vdd-l16-l28-supply = <&vreg_bob>;
176 vdd-l18-l22-supply = <&vreg_bob>;
177 vdd-l20-l24-supply = <&vreg_bob>;
178 vdd-l26-supply = <&vreg_s3a_1p35>;
179 vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
182 regulator-min-microvolt = <1352000>;
183 regulator-max-microvolt = <1352000>;
187 regulator-min-microvolt = <1904000>;
188 regulator-max-microvolt = <2040000>;
192 regulator-min-microvolt = <900000>;
193 regulator-max-microvolt = <1028000>;
201 regulator-min-microvolt = <880000>;
202 regulator-max-microvolt = <880000>;
203 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
207 regulator-min-microvolt = <1200000>;
208 regulator-max-microvolt = <1200000>;
209 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
210 regulator-always-on;
214 regulator-min-microvolt = <800000>;
215 regulator-max-microvolt = <800000>;
216 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
220 regulator-min-microvolt = <1800000>;
221 regulator-max-microvolt = <1800000>;
222 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
227 regulator-min-microvolt = <1800000>;
228 regulator-max-microvolt = <1800000>;
229 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
233 regulator-min-microvolt = <1800000>;
234 regulator-max-microvolt = <1800000>;
235 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
236 regulator-always-on;
240 regulator-min-microvolt = <1304000>;
241 regulator-max-microvolt = <1304000>;
242 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
246 regulator-min-microvolt = <2704000>;
247 regulator-max-microvolt = <2960000>;
248 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
253 regulator-min-microvolt = <3088000>;
254 regulator-max-microvolt = <3088000>;
255 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
259 regulator-min-microvolt = <3300000>;
260 regulator-max-microvolt = <3312000>;
261 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
267 regulator-min-microvolt = <1200000>;
268 regulator-max-microvolt = <1200000>;
269 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
273 regulator-min-microvolt = <2856000>;
274 regulator-max-microvolt = <3008000>;
275 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
279 pmi8998-rpmh-regulators {
280 compatible = "qcom,pmi8998-rpmh-regulators";
281 qcom,pmic-id = "b";
283 vdd-bob-supply = <&vph_pwr>;
286 regulator-min-microvolt = <3312000>;
287 regulator-max-microvolt = <3600000>;
288 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
289 regulator-allow-bypass;
293 pm8005-rpmh-regulators {
294 compatible = "qcom,pm8005-rpmh-regulators";
295 qcom,pmic-id = "c";
297 vdd-s1-supply = <&vph_pwr>;
298 vdd-s2-supply = <&vph_pwr>;
299 vdd-s3-supply = <&vph_pwr>;
300 vdd-s4-supply = <&vph_pwr>;
303 regulator-min-microvolt = <600000>;
304 regulator-max-microvolt = <600000>;
311 firmware-name = "qcom/sdm845/oneplus6/cdsp.mbn";
316 vdda-supply = <&vdda_mipi_dsi0_1p2>;
318 #address-cells = <1>;
319 #size-cells = <0>;
328 #address-cells = <1>;
329 #size-cells = <0>;
332 vddio-supply = <&vreg_l14a_1p88>;
334 reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
336 pinctrl-names = "default";
337 pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_esd_pin>;
341 remote-endpoint = <&dsi0_out>;
348 remote-endpoint = <&panel_in>;
349 data-lanes = <0 1 2 3>;
354 vdds-supply = <&vdda_mipi_dsi0_pll>;
358 protected-clocks = <GCC_QSPI_CORE_CLK>,
366 zap-shader {
367 memory-region = <&gpu_mem>;
368 firmware-name = "qcom/sdm845/oneplus6/a630_zap.mbn";
374 clock-frequency = <400000>;
376 synaptics-rmi4-i2c@20 {
377 compatible = "syna,rmi4-i2c";
379 #address-cells = <1>;
380 #size-cells = <0>;
381 interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
383 pinctrl-names = "default";
384 pinctrl-0 = <&ts_default_pins>;
386 vdd-supply = <&vreg_l28a_3p0>;
387 vio-supply = <&ts_1p8_supply>;
389 syna,reset-delay-ms = <200>;
390 syna,startup-delay-ms = <200>;
392 rmi4-f01@1 {
394 syna,nosleep-mode = <1>;
397 rmi4_f12: rmi4-f12@12 {
399 touchscreen-x-mm = <68>;
400 touchscreen-y-mm = <144>;
401 syna,sensor-type = <1>;
402 syna,rezero-wait-ms = <200>;
410 memory-region = <&ipa_fw_mem>;
411 firmware-name = "qcom/sdm845/oneplus6/ipa_fws.mbn";
425 firmware-name = "qcom/sdm845/oneplus6/mba.mbn", "qcom/sdm845/oneplus6/modem.mbn";
433 input-enable;
434 bias-pull-up;
435 qcom,drive-strength = <0>;
443 input-enable;
444 bias-pull-up;
445 qcom,drive-strength = <0>;
462 drive-strength = <2>;
463 bias-disable;
470 drive-strength = <2>;
471 bias-disable;
476 pinconf-tx {
478 drive-strength = <2>;
479 bias-disable;
482 pinconf-rx {
484 drive-strength = <2>;
485 bias-pull-up;
500 bias-pull-down;
503 rts-tx {
505 drive-strength = <2>;
506 bias-disable;
511 bias-pull-up;
519 compatible = "qcom,wcn3990-bt";
525 firmware-name = "oneplus6/crnv21.bin";
527 vddio-supply = <&vreg_s4a_1p8>;
528 vddxo-supply = <&vreg_l7a_1p8>;
529 vddrf-supply = <&vreg_l17a_1p3>;
530 vddch0-supply = <&vreg_l25a_3p3>;
531 max-speed = <3200000>;
536 label = "LS-UART1";
543 reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
545 vcc-supply = <&vreg_l20a_2p95>;
546 vcc-max-microamp = <600000>;
552 vdda-phy-supply = <&vdda_ufs1_core>;
553 vdda-pll-supply = <&vdda_ufs1_1p2>;
563 qcom,select-utmi-as-pipe-clk;
573 maximum-speed = "high-speed";
577 phy-names = "usb2-phy";
583 vdd-supply = <&vdda_usb1_ss_core>;
584 vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
585 vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
587 qcom,imp-res-offset-value = <8>;
588 qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
589 qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
590 qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
594 gpio-reserved-ranges = <0 4>, <81 4>;
600 drive-strength = <2>;
601 bias-disable;
605 ts_default_pins: ts-int {
609 drive-strength = <16>;
610 bias-pull-up;
614 panel_reset_pins: panel-reset {
618 drive-strength = <8>;
619 bias-disable = <0>;
623 panel_te_pin: panel-te {
627 drive-strength = <2>;
628 bias-disable;
629 input-enable;
633 panel_esd_pin: panel-esd {
637 drive-strength = <2>;
638 bias-pull-down;
639 input-enable;
646 vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
647 vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
648 vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
649 vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
651 qcom,snoc-host-cap-8bit-quirk;