Lines Matching +full:drive +full:- +full:strength +full:- +full:microamp
1 // SPDX-License-Identifier: GPL-2.0-only
4 /dts-v1/;
6 #include "msm8916-pm8916.dtsi"
7 #include <dt-bindings/gpio/gpio.h>
8 #include <dt-bindings/input/input.h>
9 #include <dt-bindings/interrupt-controller/irq.h>
10 #include <dt-bindings/leds/common.h>
13 * Note: The original firmware from Huawei can only boot 32-bit kernels.
14 * To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware
22 * See: https://wiki.postmarketos.org/wiki/Huawei_Ascend_G7_(huawei-g7)
34 stdout-path = "serial0";
37 gpio-keys {
38 compatible = "gpio-keys";
40 pinctrl-names = "default";
41 pinctrl-0 = <&gpio_keys_default>;
45 volume-up {
53 compatible = "gpio-leds";
55 pinctrl-names = "default";
56 pinctrl-0 = <&gpio_leds_default>;
58 led-0 {
61 default-state = "off";
65 led-1 {
68 default-state = "off";
72 led-2 {
75 default-state = "off";
80 usb_id: usb-id {
81 compatible = "linux,extcon-usb-gpio";
82 id-gpio = <&msmgpio 117 GPIO_ACTIVE_HIGH>;
83 pinctrl-names = "default";
84 pinctrl-0 = <&usb_id_default>;
92 compatible = "asahi-kasei,ak09911";
95 vdd-supply = <&pm8916_l17>;
96 vid-supply = <&pm8916_l6>;
98 reset-gpios = <&msmgpio 36 GPIO_ACTIVE_LOW>;
100 pinctrl-names = "default";
101 pinctrl-0 = <&mag_reset_default>;
105 compatible = "kionix,kx023-1025";
108 interrupt-parent = <&msmgpio>;
111 vdd-supply = <&pm8916_l17>;
112 vddio-supply = <&pm8916_l6>;
114 pinctrl-names = "default";
115 pinctrl-0 = <&accel_irq_default>;
117 mount-matrix = "-1", "0", "0",
126 interrupt-parent = <&msmgpio>;
129 vdd-supply = <&pm8916_l17>;
130 vddio-supply = <&pm8916_l6>;
132 led-max-microamp = <100000>;
133 amstaos,proximity-diodes = <1>;
135 pinctrl-names = "default";
136 pinctrl-0 = <&prox_irq_default>;
143 pinctrl-names = "default";
144 pinctrl-0 = <®_lcd_en_default>;
147 regulator-name = "outp";
148 regulator-min-microvolt = <5400000>;
149 regulator-max-microvolt = <5400000>;
150 enable-gpios = <&msmgpio 97 GPIO_ACTIVE_HIGH>;
151 regulator-active-discharge = <1>;
155 regulator-name = "outn";
156 regulator-min-microvolt = <5400000>;
157 regulator-max-microvolt = <5400000>;
158 enable-gpios = <&msmgpio 32 GPIO_ACTIVE_HIGH>;
159 regulator-active-discharge = <1>;
168 compatible = "syna,rmi4-i2c";
170 #address-cells = <1>;
171 #size-cells = <0>;
173 interrupt-parent = <&msmgpio>;
176 vdd-supply = <&pm8916_l17>;
177 vio-supply = <&pm8916_l16>;
179 pinctrl-names = "default";
180 pinctrl-0 = <&ts_irq_default>;
182 syna,startup-delay-ms = <100>;
184 rmi4-f01@1 {
186 syna,nosleep-mode = <1>; /* Allow sleeping */
189 rmi4-f11@11 {
191 syna,sensor-type = <1>; /* Touchscreen */
200 compatible = "nxp,pn547", "nxp,nxp-nci-i2c";
203 interrupt-parent = <&msmgpio>;
206 enable-gpios = <&msmgpio 20 GPIO_ACTIVE_HIGH>;
207 firmware-gpios = <&msmgpio 2 GPIO_ACTIVE_HIGH>;
209 pinctrl-names = "default";
210 pinctrl-0 = <&nfc_default>;
234 pinctrl-names = "default", "sleep";
235 pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
236 pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
242 pinctrl-names = "default", "sleep";
243 pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdhc2_cd_default>;
244 pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdhc2_cd_default>;
247 * The Huawei device tree sets cd-gpios = <&msmgpio 38 GPIO_ACTIVE_HIGH>.
257 * SD card slot and forgot to re-route to gpio38.
259 cd-gpios = <&msmgpio 56 GPIO_ACTIVE_LOW>;
272 vdd_l1_l2_l3-supply = <&pm8916_s3>;
273 vdd_l4_l5_l6-supply = <&pm8916_s4>;
274 vdd_l7-supply = <&pm8916_s4>;
277 regulator-min-microvolt = <1200000>;
278 regulator-max-microvolt = <1300000>;
282 regulator-min-microvolt = <1800000>;
283 regulator-max-microvolt = <2100000>;
287 regulator-min-microvolt = <1225000>;
288 regulator-max-microvolt = <1225000>;
292 regulator-min-microvolt = <1200000>;
293 regulator-max-microvolt = <1200000>;
297 regulator-min-microvolt = <2050000>;
298 regulator-max-microvolt = <2050000>;
302 regulator-min-microvolt = <1800000>;
303 regulator-max-microvolt = <1800000>;
307 regulator-min-microvolt = <1800000>;
308 regulator-max-microvolt = <1800000>;
312 regulator-min-microvolt = <1800000>;
313 regulator-max-microvolt = <1800000>;
317 regulator-min-microvolt = <2950000>;
318 regulator-max-microvolt = <2950000>;
322 regulator-min-microvolt = <3300000>;
323 regulator-max-microvolt = <3300000>;
327 regulator-min-microvolt = <2700000>;
328 regulator-max-microvolt = <2800000>;
332 regulator-min-microvolt = <1800000>;
333 regulator-max-microvolt = <2950000>;
334 regulator-allow-set-load;
335 regulator-system-load = <200000>;
339 regulator-min-microvolt = <1800000>;
340 regulator-max-microvolt = <2950000>;
344 regulator-min-microvolt = <3075000>;
345 regulator-max-microvolt = <3075000>;
349 regulator-min-microvolt = <1800000>;
350 regulator-max-microvolt = <3300000>;
354 regulator-min-microvolt = <1800000>;
355 regulator-max-microvolt = <3300000>;
359 regulator-min-microvolt = <1800000>;
360 regulator-max-microvolt = <1800000>;
364 regulator-min-microvolt = <2850000>;
365 regulator-max-microvolt = <2850000>;
369 regulator-min-microvolt = <2700000>;
370 regulator-max-microvolt = <2700000>;
375 accel_irq_default: accel-irq-default {
379 drive-strength = <2>;
380 bias-disable;
383 gpio_keys_default: gpio-keys-default {
387 drive-strength = <2>;
388 bias-pull-up;
391 gpio_leds_default: gpio-leds-default {
395 drive-strength = <2>;
396 bias-disable;
399 nfc_default: nfc-default {
403 drive-strength = <2>;
404 bias-disable;
407 mag_reset_default: mag-reset-default {
411 drive-strength = <2>;
412 bias-disable;
415 prox_irq_default: prox-irq-default {
419 drive-strength = <2>;
420 bias-disable;
423 reg_lcd_en_default: reg-lcd-en-default {
427 drive-strength = <2>;
428 bias-disable;
431 sdhc2_cd_default: sdhc2-cd-default {
435 drive-strength = <2>;
436 bias-disable;
439 ts_irq_default: ts-irq-default {
443 drive-strength = <2>;
444 bias-disable;
447 usb_id_default: usb-id-default {
451 drive-strength = <8>;
452 bias-pull-up;