Lines Matching +full:ext +full:- +full:reset +full:- +full:output

1 // SPDX-License-Identifier: GPL-2.0 OR X11
6  * Author: Markus Niebel <Markus.Niebel@tq-group.com>
13 		/* 512 MB - default configuration */
19 	cpu-supply = <&sw1a_reg>;
23 	pinctrl-names = "default";
24 	pinctrl-0 = <&pinctrl_i2c1>;
25 	clock-frequency = <100000>;
29 		pinctrl-names = "default";
30 		pinctrl-0 = <&pinctrl_pmic1>;
36 				regulator-min-microvolt = <700000>;
37 				regulator-max-microvolt = <3300000>;
38 				regulator-boot-on;
39 				regulator-always-on;
40 				regulator-ramp-delay = <6250>;
45 				regulator-min-microvolt = <700000>;
46 				regulator-max-microvolt = <1475000>;
47 				regulator-boot-on;
48 				regulator-always-on;
49 				regulator-ramp-delay = <6250>;
53 				regulator-min-microvolt = <1500000>;
54 				regulator-max-microvolt = <1850000>;
55 				regulator-boot-on;
56 				regulator-always-on;
60 				regulator-min-microvolt = <900000>;
61 				regulator-max-microvolt = <1650000>;
62 				regulator-boot-on;
63 				regulator-always-on;
67 				regulator-min-microvolt = <5000000>;
68 				regulator-max-microvolt = <5150000>;
72 				regulator-min-microvolt = <1000000>;
73 				regulator-max-microvolt = <3000000>;
74 				regulator-boot-on;
75 				regulator-always-on;
79 				regulator-boot-on;
80 				regulator-always-on;
84 				regulator-min-microvolt = <1800000>;
85 				regulator-max-microvolt = <3300000>;
86 				regulator-always-on;
90 				regulator-min-microvolt = <800000>;
91 				regulator-max-microvolt = <1550000>;
92 				regulator-always-on;
96 				regulator-min-microvolt = <2850000>;
97 				regulator-max-microvolt = <3300000>;
98 				regulator-always-on;
102 				regulator-min-microvolt = <2850000>;
103 				regulator-max-microvolt = <3300000>;
104 				regulator-always-on;
108 				regulator-min-microvolt = <1800000>;
109 				regulator-max-microvolt = <3300000>;
110 				regulator-always-on;
114 				regulator-min-microvolt = <1800000>;
115 				regulator-max-microvolt = <3300000>;
116 				regulator-always-on;
122 	se97b: temperature-sensor-eeprom@1e {
123 		compatible = "nxp,se97b", "jedec,jc-42.4-temp";
225 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
226 	pinctrl-0 = <&pinctrl_usdhc3>;
227 	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
228 	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
229 	assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
230 	assigned-clock-rates = <400000000>;
231 	bus-width = <8>;
232 	non-removable;
233 	vmmc-supply = <&vgen4_reg>;
234 	vqmmc-supply = <&sw2_reg>;
239 	pinctrl-names = "default";
240 	pinctrl-0 = <&pinctrl_wdog1>;
243 	 * WDOG reset needs to run with WDOG_RESET_B signal enabled.
244 	 * X1-51 (WDOG1#) signal needs carrier board handling to reset
245 	 * TQMa7 on X1-22 (RESET_IN#).
247 	fsl,ext-reset-output;