Lines Matching +full:sama5d2 +full:- +full:adc
1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
3 * at91-sama5d27_wlsom1_ek.dts - Device Tree file for SAMA5D27 WLSOM1 EK
9 /dts-v1/;
10 #include "at91-sama5d27_wlsom1.dtsi"
11 #include <dt-bindings/input/input.h>
15 …compatible = "microchip,sama5d27-wlsom1-ek", "microchip,sama5d27-wlsom1", "atmel,sama5d27", "atmel…
26 stdout-path = "serial0:115200n8";
30 compatible = "gpio-keys";
32 pinctrl-names = "default";
33 pinctrl-0 = <&pinctrl_key_gpio_default>;
40 wakeup-source;
45 compatible = "gpio-leds";
46 pinctrl-names = "default";
47 pinctrl-0 = <&pinctrl_led_gpio_default>;
63 linux,default-trigger = "heartbeat";
68 &adc {
69 vddana-supply = <&vdd_3v3>;
70 vref-supply = <&vdd_3v3>;
71 pinctrl-names = "default";
72 pinctrl-0 = <&pinctrl_adc_default>;
77 atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
81 pinctrl-0 = <&pinctrl_flx0_default>;
82 pinctrl-names = "default";
83 atmel,use-dma-rx;
84 atmel,use-dma-tx;
93 atmel,use-dma-rx;
94 atmel,use-dma-tx;
105 * There is no real pinmux for ADC, if the pin
108 * Requesting pins for ADC is GPIO is
111 * state when the pin is not muxed to the adc.
116 bias-disable;
122 bias-disable;
127 bias-pull-up;
134 bias-pull-down;
144 bias-disable;
152 bias-disable;
159 bias-disable;
165 bias-disable;
171 bias-disable;
176 bias-disable;
181 bias-disable;
186 pinctrl-names = "default";
187 pinctrl-0 = <&pinctrl_pwm0_default>;
200 bus-width = <4>;
201 mmc-ddr-3_3v;
202 pinctrl-names = "default";
203 pinctrl-0 = <&pinctrl_sdmmc0_default>;
208 debounce-delay-us = <976>;
209 atmel,wakeup-rtc-timer;
218 compatible = "atmel,tcb-timer";
223 compatible = "atmel,tcb-timer";
229 pinctrl-names = "default";
230 pinctrl-0 = <&pinctrl_uart0_default>;
231 atmel,use-dma-rx;
232 atmel,use-dma-tx;
237 pinctrl-names = "default";
238 pinctrl-0 = <&pinctrl_uart3_default>;
239 atmel,use-dma-rx;
240 atmel,use-dma-tx;
245 atmel,vbus-gpio = <&pioA PIN_PA16 GPIO_ACTIVE_HIGH>;
246 pinctrl-names = "default";
247 pinctrl-0 = <&pinctrl_usba_vbus>;
252 num-ports = <3>;
253 atmel,vbus-gpio = <0
257 pinctrl-names = "default";
258 pinctrl-0 = <&pinctrl_usb_default>;