Lines Matching +full:delay +full:- +full:line

1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mmc/fsl-imx-esdhc.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10   - Shawn Guo <shawnguo@kernel.org>
13   - $ref: "mmc-controller.yaml"
20   by mmc.txt and the properties used by the sdhci-esdhc-imx driver.
25       - enum:
26           - fsl,imx25-esdhc
27           - fsl,imx35-esdhc
28           - fsl,imx51-esdhc
29           - fsl,imx53-esdhc
30           - fsl,imx6q-usdhc
31           - fsl,imx6sl-usdhc
32           - fsl,imx6sll-usdhc
33           - fsl,imx6sx-usdhc
34           - fsl,imx6ull-usdhc
35           - fsl,imx7d-usdhc
36           - fsl,imx7ulp-usdhc
37       - items:
38           - enum:
39               - fsl,imx8mm-usdhc
40               - fsl,imx8mn-usdhc
41               - fsl,imx8mp-usdhc
42               - fsl,imx8mq-usdhc
43               - fsl,imx8qm-usdhc
44               - fsl,imx8qxp-usdhc
45           - const: fsl,imx7d-usdhc
53   fsl,wp-controller:
58   fsl,delay-line:
61       Specify the number of delay cells for override mode.
62       This is used to set the clock delay for DLL(Delay Line) on override mode
65       chapter, DLL (Delay Line) section in RM for details.
68   voltage-ranges:
69     $ref: '/schemas/types.yaml#/definitions/uint32-matrix'
77         - description: value for minimum slot voltage
78         - description: value for maximum slot voltage
81   fsl,tuning-start-tap:
84       Specify the start delay cell point when send first CMD19 in tuning procedure.
87   fsl,tuning-step:
90       Specify the increasing delay cell steps in tuning procedure.
91       The uSDHC use one delay cell as default increasing step to do tuning process.
92       This property allows user to change the tuning step to more than one delay
94       tuning step can't find the proper delay window within limited tuning retries.
97   fsl,strobe-dll-delay-target:
100       Specify the strobe dll control slave delay target.
101       This delay target programming host controller loopback read clock, and this
102       property allows user to change the delay target for the strobe input read clock.
103       If not use this property, driver default set the delay target to value 7.
112   clock-names:
114       - const: ipg
115       - const: ahb
116       - const: per
118   pinctrl-names:
120       - minItems: 3
122           - const: default
123           - const: state_100mhz
124           - const: state_200mhz
125           - const: sleep
126       - minItems: 1
128           - const: default
129           - const: sleep
132   - compatible
133   - reg
134   - interrupts
139   - |
141         compatible = "fsl,imx51-esdhc";
144         fsl,wp-controller;
148         compatible = "fsl,imx51-esdhc";
151         cd-gpios = <&gpio1 6 0>; /* GPIO1_6 */
152         wp-gpios = <&gpio1 5 0>; /* GPIO1_5 */