Lines Matching full:you
26 This selects the ARM(R) AMBA(R) PrimeCell PL010 UART. If you have
27 an Integrator/AP or Integrator/PP2 platform, or if you have a
37 Say Y here if you wish to use an AMBA PrimeCell UART as the system
41 Even if you say Y here, the currently visible framebuffer console
43 you can alter that using a kernel command line option such as
53 This selects the ARM(R) AMBA(R) PrimeCell PL011 UART. If you have
65 Say Y here if you wish to use an AMBA PrimeCell UART as the system
69 Even if you say Y here, the currently visible framebuffer console
71 you can alter that using a kernel command line option such as
121 If you say Y here, it will be possible to use a serial port as the
143 Say Y here if you wish to use an on-chip UART on a Atmel
153 Say Y here if you wish to use the PDC to do DMA transfers to
167 Say Y here if you wish to have the internal AT91 UARTs
170 64). This is necessary if you also want other UARTs, such as
175 To use this, you should create suitable ttyATn device nodes in
178 Say Y if you have an external 8250/16C550 UART. If unsure, say N.
184 This special driver allows you to temporary use NMI debugger port
187 Unlike KDB's disable_nmi command, with this driver you are always
193 communication methods, for things like PPP you still must fully
213 Say Y here if you wish to use a Amlogic MesonX UART as the
232 Even if you say Y here, the currently visible virtual console
234 you can alter that using a kernel command line option such as
272 Even if you say Y here, the currently visible virtual console
274 you can alter that using a kernel command line option such as
294 Even if you say Y here, the currently visible virtual console
296 you can alter that using a kernel command line option such as
327 If you say Y here, it will be possible to use a the Tegra TCU as the
352 Say Y here if you want to support this ICs.
369 If you say Y here, it will be possible to use a serial port as the
399 If you say Y here, it will be possible to use a serial port as the
414 If you have a machine based on a 21285 (Footbridge) StrongARM(R)/
415 PCI bridge you can enable its onboard serial port by enabling this
423 If you have enabled the serial port on the 21285 footbridge you can
426 Even if you say Y here, the currently visible virtual console
428 you can alter that using a kernel command line option such as
440 If you have a machine based on an Intel XScale PXA2xx CPU you
443 Unless you have a specific need, you should use SERIAL_8250_PXA
456 If you have enabled the serial port on the Intel XScale PXA
457 CPU you can make it the console by answering Y to this option.
459 Even if you say Y here, the currently visible virtual console
461 you can alter that using a kernel command line option such as
466 Unless you have a specific need, you should use SERIAL_8250_PXA
475 If you have a machine based on a SA1100/SA1110 StrongARM(R) CPU you
485 If you have enabled the serial port on the SA1100/SA1110 StrongARM
486 CPU you can make it the console by answering Y to this option.
488 Even if you say Y here, the currently visible virtual console
490 you can alter that using a kernel command line option such as
502 If you have a machine based on a Motorola IMX CPU you
510 If you have enabled the serial port on the Freescale IMX
511 CPU you can make it the console by answering Y/M to this option.
513 Even if you say Y/M here, the currently visible virtual console
515 you can alter that using a kernel command line option such as
527 If you have enabled the earlycon on the Freescale IMX
528 CPU you can make it the earlycon by answering Y to this option.
535 Say Y here if you want to use the Xilinx uartlite serial controller.
546 Say Y here if you wish to use a Xilinx uartlite as the system
557 you think you might implement.
571 systems. Say Y or M if you want to be able to these serial ports.
577 If you would like to be able to use the Zilog8530 serial port
578 on your Sparc system as the console, you can do so by answering
586 mouse on (PCI) UltraSPARC systems. Say Y or M if you want to be able
593 If you would like to be able to use the SU serial port
594 on your Sparc system as the console, you can do so by answering
612 3. Add device ttyB0 to /etc/securetty (if you want to log on as
633 3. Add device ttyB0 to /etc/securetty (if you want to log on as
642 (PCI) UltraSPARC systems. Say Y or M if you want to be able to these
649 If you would like to be able to use the SAB82532 serial port
650 on your Sparc system as the console, you can do so by answering
658 systems. Say Y if you want to be able to use this device.
666 systems. Say Y or M if you want to be able to these serial ports.
712 If you have a MIPS-based Philips SoC such as PNX8330 and you want
720 If you have a MIPS-based Philips SoC such as PNX8330 and you want
739 If you would like to be able to use one of the high speed serial
740 ports on the LPC32XX as the console, you can do so by answering
764 This setting lets you define what the default baudrate is for the
782 Say Y or M if you want to be able to these serial ports.
791 the two drivers being unable to coexist; you could not use
801 If you enable this option, any z85c30 ports in the system will
802 be registered as ttyS0 onwards as in the past, and you will be
806 Say N unless you need the z85c30 ports on your (Power)Mac
814 If you would like to be able to use the z85c30 serial port
815 on your (Power)Mac as the console, you can do so by answering
831 Say Y here if you wish to use a SCC or SMC CPM UART as the system
835 Even if you say Y here, the currently visible framebuffer console
837 you can alter that using a kernel command line option such as
847 If you have a PIC32, this driver supports the serial ports.
858 If you have a PIC32, this driver supports the putting a console on one
868 This driver supports MPC52xx and MPC512x PSC serial ports. If you would
869 like to use them, you must answer Y or M to this option. Note that
878 Select this options if you'd like to use one of the PSC serial port
931 If you have a NEC VR4100 series processor and you want to use
940 If you have a NEC VR4100 series processor and you want to use
949 of cards which provide multiple serial ports. You would need
954 If you have a card like this, say Y here, otherwise say N.
1000 If you have a machine based on an Texas Instruments OMAP CPU you
1003 By enabling this option you take advantage of dma feature available
1012 Select this option if you would like to use omap serial port as
1015 Even if you say Y here, the currently visible virtual console
1017 you can alter that using a kernel command line option such as
1027 Select this option if you are building a kernel for a device that
1037 Select this option if you would like to use a SiFive UART as the
1040 Even if you say Y here, the currently visible virtual console
1042 you can alter that using a kernel command line option such as
1062 Select this option if you would like to use a Lantiq UART as the
1112 You must select at least one bus for the driver to be built.
1124 You must select at least one bus for the driver to be built.
1152 If you have enabled the serial port on the BCM63xx CPU
1153 you can make it the console by answering Y to this option.
1202 This setting lets you define the maximum number of the Altera
1211 This setting lets you define what the default baudrate is for the
1251 Say Y here if you wish to use the PCH UART as the system console
1293 If you have an Atheros AR933X SOC based board and want to use the
1311 Set this to the number of serial ports you want the driver
1361 Set this to the number of serial ports you want the driver
1377 If you want to compile this driver into the kernel, say Y here. If
1378 you don't have a suitable RocketPort card installed, say N.
1401 If you have enabled the lpuart serial port on the Freescale SoCs,
1402 you can make it the console by answering Y to this option.
1417 If you have enabled the LINFlexD UART serial port on the Freescale
1418 SoCs, you can make it the console by answering Y to this option.
1432 If you have enabled the USART serial port on Conexant Digicolor
1433 SoCs, you can make it the console by answering Y to this option.
1504 This driver is for Marvell EBU SoC's UART. If you have a machine
1517 Say 'Y' here if you wish to use Armada-3700 UART as the system console.
1528 Say 'Y' here if you wish to use the on-board serial port.
1538 Say 'Y' here if you wish to use Actions Semiconductor S500/S900 UART
1547 Say 'Y' here if you wish to use the on-board serial port.
1557 Say 'Y' here if you wish to use the RDA8810PL UART as the system
1581 Say 'Y' here if you wish to use a USIO/UART of Socionext Milbeaut