Lines Matching full:console
14 the console before standard serial driver is probed. The console is
33 bool "Support for console on AMBA serial port"
38 console (the system console is the device which receives all kernel
41 Even if you say Y here, the currently visible framebuffer console
42 (/dev/tty0) will still be used as the system console by default, but
44 "console=ttyAM0". (Try "man bootparam" or see the documentation of
60 bool "Support for console on AMBA serial port"
66 console (the system console is the device which receives all kernel
69 Even if you say Y here, the currently visible framebuffer console
70 (/dev/tty0) will still be used as the system console by default, but
72 "console=ttyAMA0". (Try "man bootparam" or see the documentation of
77 bool "Early console using ARM semihosting"
83 Support for early debug console using ARM semihosting. This enables
84 the console before standard serial driver is probed. This is enabled
85 with "earlycon=smh" on the kernel command line. The console is
89 bool "Early console using RISC-V SBI"
95 Support for early debug console using RISC-V SBI. This enables
96 the console before standard serial driver is probed. This is enabled
97 with "earlycon=sbi" on the kernel command line. The console is
116 bool "Support for console on a BCM1xxx DUART serial port"
122 system console (the system console is the device which receives all
139 bool "Support for console on AT91 serial port"
144 AT91 processor as the system console (the system
145 console is the device which receives all kernel messages and
176 /dev/, and pass "console=ttyATn" to the kernel.
181 bool "Serial console over KGDB NMI debugger port"
185 as a normal console (assuming that the port is attached to KGDB).
189 This is because this console driver processes the input in NMI
192 Note that since the console interprets input and uses polling
195 use raw console.
208 bool "Support for console on meson"
214 system console (the system console is the device which
228 bool "Support for console on CLPS711X serial port"
232 Even if you say Y here, the currently visible virtual console
233 (/dev/tty0) will still be used as the system console by default, but
235 "console=ttyCL1".
264 bool "Support for console on Samsung SoC serial port"
270 an virtual console.
272 Even if you say Y here, the currently visible virtual console
273 (/dev/tty0) will still be used as the system console by default, but
275 "console=ttySACx". (Try "man bootparam" or see the documentation of
290 bool "Support for console on SiRF SoC serial port"
294 Even if you say Y here, the currently visible virtual console
295 (/dev/tty0) will still be used as the system console by default, but
297 "console=ttySiRFx". (Try "man bootparam" or see the documentation of
322 bool "Support for console on a Tegra TCU serial port"
328 system console (the system console is the device which receives all
364 bool "Support console on DECstation DZ serial driver"
370 system console (the system console is the device which receives all
374 Note that the firmware uses ttyS3 as the serial console on
394 bool "Support for console on a DECstation Z85C30 serial port"
400 system console (the system console is the device which receives all
404 Note that the firmware uses ttyS1 as the serial console on the
419 bool "Console on DC21285 serial port"
424 make it the console by answering Y to this option.
426 Even if you say Y here, the currently visible virtual console
427 (/dev/tty0) will still be used as the system console by default, but
429 "console=ttyFB". (Try "man bootparam" or see the documentation of
451 bool "Console on PXA serial port (DEPRECATED)"
457 CPU you can make it the console by answering Y to this option.
459 Even if you say Y here, the currently visible virtual console
460 (/dev/tty0) will still be used as the system console by default, but
462 "console=ttySA0". (Try "man bootparam" or see the documentation of
481 bool "Console on SA1100 serial port"
486 CPU you can make it the console by answering Y to this option.
488 Even if you say Y here, the currently visible virtual console
489 (/dev/tty0) will still be used as the system console by default, but
491 "console=ttySA0". (Try "man bootparam" or see the documentation of
506 tristate "Console on IMX serial port"
511 CPU you can make it the console by answering Y/M to this option.
513 Even if you say Y/M here, the currently visible virtual console
514 (/dev/tty0) will still be used as the system console by default, but
516 "console=ttymxc0". (Try "man bootparam" or see the documentation of
541 bool "Support for console on Xilinx uartlite serial port"
547 console (the system console is the device which receives all kernel
574 bool "Console on Sun Zilog8530 serial port"
578 on your Sparc system as the console, you can do so by answering
590 bool "Console on Sun SU serial port"
594 on your Sparc system as the console, you can do so by answering
607 software console. The following steps need to be completed to use
613 root on this console.)
614 4. Change the kernel command console parameter to: console=ttyB0
617 bool "Support for console on serial MUX"
623 bool "PDC software console support"
626 Saying Y here will enable the software based PDC console to be
627 used as the system console. This is useful for machines in
628 which the hardware based console has not been written yet. The
629 following steps must be completed to use the PDC console:
634 root on this console.)
635 4. Change the kernel command console parameter to: console=ttyB0
646 bool "Console on Sun Siemens SAB82532 serial port"
650 on your Sparc system as the console, you can do so by answering
654 bool "Sun4v Hypervisor Console support"
657 This driver supports the console device found on SUN4V Sparc
669 bool "Console on SGI Zilog8530 serial port"
690 bool "Support for console on SuperH SCI(F)" if EXPERT
696 bool "Support for early console on SuperH SCI(F)" if EXPERT
716 bool "Enable PNX8XX0 serial console"
721 to use serial console, say Y. Otherwise, say N.
735 bool "Enable LPC32XX high speed UART serial console"
740 ports on the LPC32XX as the console, you can do so by answering
769 bool "Coldfire serial console support"
773 Enable a ColdFire internal serial port to be the system console.
810 bool "Console on Mac or PowerMac z85c30 serial port"
815 on your (Power)Mac as the console, you can do so by answering
827 bool "Support for console on CPM SCC/SMC serial port"
832 console (the system console is the device which receives all kernel
835 Even if you say Y here, the currently visible framebuffer console
836 (/dev/tty0) will still be used as the system console by default, but
838 "console=ttyCPM0". (Try "man bootparam" or see the documentation of
850 to use a serial port as a console, this must be included in kernel and
854 bool "PIC32 serial console support"
858 If you have a PIC32, this driver supports the putting a console on one
861 Say Y to use the PIC32 console, otherwise say N.
870 for use as console, it must be included in kernel and not as a
874 bool "Console on a Freescale MPC52xx/MPC512x family PSC serial port"
879 of the Freescale MPC52xx family as a console.
886 Select the MPC52xx console baud rate.
888 console baudrate
918 bool "TMPTX39XX/49XX SIO Console support"
936 bool "Enable NEC VR4100 series Serial Interface Unit console"
941 a console on a serial port, say Y. Otherwise, say N.
965 bool "MSM serial console support"
977 bool "QCOM GENI Serial Console support"
982 Serial console driver for Qualcomm Technologies Inc's GENI based
991 bool "VIA VT8500 serial console support"
1008 bool "Console on OMAP serial port"
1013 console.
1015 Even if you say Y here, the currently visible virtual console
1016 (/dev/tty0) will still be used as the system console by default, but
1018 "console=ttyOx". (Try "man bootparam" or see the documentation of
1032 bool "Console on SiFive UART"
1038 system console.
1040 Even if you say Y here, the currently visible virtual console
1041 (/dev/tty0) will still be used as the system console by default, but
1043 "console=ttySIFx". (Try "man bootparam" or see the documentation of
1057 bool "Console on Lantiq UART"
1063 system console.
1083 bool "Console on SCCNXP serial port"
1087 Support for console on SCCNXP serial ports.
1144 BCM7xxx (STB) - DOCSIS console
1147 bool "Console on BCM63xx serial port"
1153 you can make it the console by answering Y to this option.
1163 bool "Console on GRLIB APBUART serial port"
1167 Support for running a console on the GRLIB APBUART
1176 bool "Altera JTAG UART console support"
1181 Enable a Altera JTAG UART port to be the system console.
1188 Bypass console output and keep going even if there is no
1216 bool "Altera UART console support"
1221 Enable a Altera UART port to be the system console.
1247 bool "Support for console on Intel EG20T PCH UART/OKI SEMICONDUCTOR ML7213 IOH"
1251 Say Y here if you wish to use the PCH UART as the system console
1252 (the system console is the device which receives all kernel messages and
1265 bool "MXS AUART console support"
1269 Enable a MXS AUART port to be the system console.
1280 bool "Cadence UART console support"
1285 Enable a Cadence UART port to be the system console.
1300 bool "Console on AR933X serial port"
1304 Enable a built-in UART port of the AR933X to be the system console.
1323 bool "MPS2 UART console support"
1336 bool "EFM32 UART/USART console support"
1348 bool "Console on ARC UART"
1353 Enable system Console on ARC UART
1396 bool "Console on Freescale lpuart serial port"
1402 you can make it the console by answering Y to this option.
1412 bool "Console on Freescale LINFlexD UART serial port"
1418 SoCs, you can make it the console by answering Y to this option.
1428 bool "Console on Conexant Digicolor serial port"
1433 SoCs, you can make it the console by answering Y to this option.
1448 bool "Support for console on ST ASC"
1471 bool "Spreadtrum UART console support"
1476 Support for early debug console using Spreadtrum's serial. This enables
1477 the console before standard serial driver is probed. This is enabled
1478 with "earlycon" on the kernel command line. The console is
1495 bool "Support for console on STM32"
1511 bool "Console on Marvell EBU serial port"
1517 Say 'Y' here if you wish to use Armada-3700 UART as the system console.
1518 (the system console is the device which receives all kernel messages
1532 bool "Console on Actions Semi Owl serial port"
1539 as the system console.
1551 bool "Console on RDA Micro serial port"
1558 console. Only earlycon is implemented currently.
1575 bool "Support for console on MILBEAUT USIO/UART serial port"
1582 SoCs as the system console (the system console is the device which