17  * 	Scan LUN 0; if the target responds to LUN 0 (even if there is no
23  * 		If target is SCSI-3 or up, issue a REPORT LUN, and scan
25  * 		sequentially scan LUNs up until some maximum is reached,
102 module_param_string(scan, scsi_scan_type, sizeof(scsi_scan_type),
104 MODULE_PARM_DESC(scan, "sync, async, manual, or none. "
106 		 "for manual device scan via the 'scan' sysfs attribute.");
129  * this function was called will have finished its scan.  Hosts which
381 	 * means it was allocated but never made visible (because a scan  in scsi_target_reap_ref_release()
579 				"scsi scan: INQUIRY pass %d length %d\n",  in scsi_probe_lun()
598 				"scsi scan: INQUIRY %s with code 0x%x\n",  in scsi_probe_lun()
667 			    "scsi scan: %d byte inquiry failed.  "  in scsi_probe_lun()
704 				    "scsi scan: INQUIRY result too short (%d),"  in scsi_probe_lun()
776 	 * that can correctly scan.  in scsi_add_lun()
937 			    "in wrong state %s to complete scan\n",  in scsi_add_lun()
1028  *              needed on first scan
1055 	 * The rescan flag is used as an optimization, the first scan of a  in scsi_probe_and_add_lun()
1062 				"scsi scan: device exists on %s\n",  in scsi_probe_and_add_lun()
1105 		SCSI_LOG_SCAN_BUS(2, sdev_printk(KERN_INFO, sdev, "scsi scan:"  in scsi_probe_and_add_lun()
1114 					"scsi scan: consider passing scsi_mod."  in scsi_probe_and_add_lun()
1150 					"scsi scan: peripheral device type"  in scsi_probe_and_add_lun()
1183  * scsi_sequential_lun_scan - sequentially scan a SCSI target
1184  * @starget:	pointer to target structure to scan
1190  *     Generally, scan from LUN 1 (LUN 0 is assumed to already have been
1205 		"scsi scan: Sequential scan\n"));  in scsi_sequential_lun_scan()
1210 	 * override the other settings, and scan all of them. Normally,  in scsi_sequential_lun_scan()
1227 	 * scan any SCSI_1 device for non-0 luns, but that check would best  in scsi_sequential_lun_scan()
1238 	 * the other settings, and scan all of them.  in scsi_sequential_lun_scan()
1248 	 * Do not scan SCSI-2 or lower device past LUN 7, unless  in scsi_sequential_lun_scan()
1269  * scsi_report_lun_scan - Scan using SCSI REPORT LUN results
1272  * @rescan: nonzero if we can skip code only needed on first scan
1276  *   Scan the resulting list of LUNs by calling scsi_probe_and_add_lun.
1278  *   If BLINK_REPORTLUN2 is set, scan a target that supports more than 8
1285  *     0: scan completed (or no memory, so further scanning is futile)
1286  *     1: could not scan with REPORT LUN
1373 				"scsi scan: Sending REPORT LUNS to (try %d)\n",  in scsi_report_lun_scan()
1381 				"scsi scan: REPORT LUNS"  in scsi_report_lun_scan()
1416 		"scsi scan: REPORT LUN scan\n"));  in scsi_report_lun_scan()
1419 	 * Scan the luns in lun_data. The entry at offset 0 is really  in scsi_report_lun_scan()
1440 					" from lun %llu while scanning, scan"  in scsi_report_lun_scan()
1452 		 * the sdev we used didn't appear in the report luns scan  in scsi_report_lun_scan()
1540 		 * Don't scan the host adapter  in __scsi_scan_target()
1551 		 * Scan for a specific host/chan/id/lun.  in __scsi_scan_target()
1558 	 * Scan LUN 0, if there is some response, scan further. Ideally, we  in __scsi_scan_target()
1565 			 * The REPORT LUN did not scan the target,  in __scsi_scan_target()
1566 			 * do a sequential scan.  in __scsi_scan_target()
1584  * scsi_scan_target - scan a target id, possibly including all LUNs on the target.
1585  * @parent:	host to scan
1586  * @channel:	channel to scan
1587  * @id:		target id to scan
1588  * @lun:	Specific LUN to scan or SCAN_WILD_CARD
1592  *              'scan=manual' is set.
1595  *     Scan the target id on @parent, @channel, and @id. Scan at least LUN 0,
1598  *     First try a REPORT LUN scan, if that does not scan the target, do a
1599  *     sequential scan of LUNs on the target id.
1644 				 * Scan from high to low id.  in scsi_scan_channel()
1706  * scsi_prep_async_scan - prepare for an async scan
1710  * Tells the midlayer this host is going to do an asynchronous scan.
1757  * scsi_finish_async_scan - asynchronous scan has finished
1832  * scsi_scan_host - scan the given adapter
1833  * @shost:	adapter to scan