Lines Matching +full:4 +full:ghz +full:- +full:coexistence
8 * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved.
29 * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
33 * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved.
71 /* uCode version contains 4 values: Major/Minor/API/Serial */
78 #define IL_CCK_RATES 4
92 /* Multi-Station support */
131 /* Bluetooth device coexistence config command */
138 /* RF-KILL commands and notifications */
184 * when sending the response to each driver-originated command, so
196 * 0:7 tfd idx - position within TX queue
199 * 14 huge - driver sets this to indicate command is in the
201 * 15 unsolicited RX or uCode-originated notification
215 * 1) DSP gain (or sometimes called DSP attenuation). This is a fine-grained
248 * High-throughput (HT) rate format for bits 7:0 (bit 8 must be "1"):
249 * 2-0: 0) 6 Mbps
253 * 4) 36 Mbps
258 * 4-3: 0) Single stream (SISO)
265 * 3-0: 0xD) 6 Mbps
275 * 6-0: 10) 1 Mbps
445 * a 256-entry history of uCode execution within a circular buffer.
456 * __le32 event_id; range 0 - 1500
458 * __le32 data; event_id-specific data value
474 * __le32 data1; error-specific data
475 * __le32 data2; error-specific data
547 RXON_DEV_TYPE_IBSS = 4,
555 #define RXON_RX_CHAIN_FORCE_SEL_MSK cpu_to_le16(0x7 << 4)
556 #define RXON_RX_CHAIN_FORCE_SEL_POS (4)
575 #define RXON_FLG_SHORT_SLOT_MSK cpu_to_le32(1 << 4)
585 /* rx response to host with 8-byte TSF
623 /* accept multi-cast */
625 /* don't decrypt uni-cast frames */
627 /* don't decrypt multi-cast frames */
628 #define RXON_FILTER_DIS_GRP_DECRYPT_MSK cpu_to_le32(1 << 4)
641 * RXON_FILTER_ASSOC_MSK to 0. This will clear station-dependent
739 #define IL_MAX_UCODE_BEACON_INTERVAL 4 /* 4096 */
784 __le32 status; /* 0 - OK, 1 - fail */
789 * Quality-of-Service (QOS) Commands & Responses:
794 * struct il_ac_qos -- QOS timing params for C_QOS_PARAM
795 * One for each of 4 EDCA access categories in struct il_qosparam_cmd
798 * Should be a power-of-2, minus 1. Device's default is 0x0f.
800 * Should be a power-of-2, minus 1. Device's default is 0x3f.
823 #define AC_NUM 4
828 * This command sets up timings for each of the 4 prioritized EDCA Tx FIFOs
882 /* wep key in STA: 5-bytes (0) or 13-bytes (1) */
897 #define BUILD_RAxTID(sta_id, tid) (((sta_id) << 4) + (tid))
903 __le16 tkip_rx_ttak[5]; /* 10-byte unicast TKIP TTAK */
906 u8 key[16]; /* 16-byte unicast decryption key */
916 * or the idx to a pre-existing station entry when modifying that station.
932 * The device contains an internal table of per-station information,
939 * a new entry, or modifying a pre-existing one.
971 /* TID for which to add block-ack support.
975 /* TID for which to remove block-ack support.
979 /* Starting Sequence Number for added block-ack support.
999 /* TID for which to add block-ack support.
1003 /* TID for which to remove block-ack support.
1007 /* Starting Sequence Number for added block-ack support.
1013 * it is asleep -- used to synchronise PS-poll and u-APSD
1037 /* TID for which to add block-ack support.
1041 /* TID for which to remove block-ack support.
1045 /* Starting Sequence Number for added block-ack support.
1051 * it is asleep -- used to synchronise PS-poll and u-APSD
1119 #define WEP_KEYS_MAX 4
1125 * (4)
1138 #define RX_RES_PHY_FLAGS_ANTENNA_POS 4
1201 #define IL39_RX_FRAME_SIZE (4 + sizeof(struct il3945_rx_frame))
1203 /* Fixed (non-configurable) rx data from phy */
1206 #define IL49_RX_PHY_FLAGS_ANTENNAE_OFFSET (4)
1211 __le16 ant_selection; /* ant A bit 4, ant B bit 5, ant C bit 6 */
1213 u8 rssi_info[6]; /* we use even entries, 0/2/4 for A/B/C rssi */
1227 __le32 beacon_time_stamp; /* beacon at on-air rise */
1232 __le16 byte_count; /* frame's byte-count */
1254 * handle reception of block-acks; uCode updates the host driver via
1269 * 1: Use Request-To-Send protocol before this frame.
1275 * 1: Transmit Clear-To-Send to self before this frame.
1276 * Driver should set this for AUTH/DEAUTH/ASSOC-REQ/REASSOC mgmnt frames.
1292 #define TX_CMD_FLG_STA_RATE_MSK cpu_to_le32(1 << 4)
1294 /* 1: Expect immediate block-ack.
1295 * Set when Txing a block-ack request frame. Also set TX_CMD_FLG_ACK_MSK. */
1299 * 1: Frame requires full Tx-Op protection.
1312 * Set this for management frames, non-QOS data frames, non-unicast frames,
1316 /* 1: This frame is non-last MPDU; more fragments are coming.
1334 * 0 - no CCMP encryption; 1 - CCMP encryption */
1337 /* HCCA-AP - disable duration overwriting. */
1360 * + 8-byte MIC (not used for CCM/WEP)
1361 * NOTE: Does not include Tx command bytes, post-MAC pad bytes,
1362 * MIC (CCM) 8 bytes, ICV (WEP/TKIP/CKIP) 4 bytes, CRC 4 bytes.i
1363 * Range: 14-2342 bytes.
1385 __le16 word[4];
1402 * Duration of EDCA burst Tx Opportunity, in 32-usec units.
1429 * Used for managing Tx retries when expecting block-acks.
1444 * + 8-byte MIC (not used for CCM/WEP)
1445 * NOTE: Does not include Tx command bytes, post-MAC pad bytes,
1446 * MIC (CCM) 8 bytes, ICV (WEP/TKIP/CKIP) 4 bytes, CRC 4 bytes.i
1447 * Range: 14-2342 bytes.
1477 * rate (via non-0 value) for special frames (e.g. management), while
1504 * Duration of EDCA burst Tx Opportunity, in 32-usec units.
1662 * 2 or more frames that used block-acknowledge. All frames were
1666 * Note that, for aggregation, ACK (block-ack) status is not delivered here;
1667 * block-ack has not been received by the time the 4965 device records
1684 /* For non-agg: Rate at which frame was successful.
1688 /* For non-agg: RTS + CTS + frame tx attempts time + ACK.
1689 * For agg: RTS + CTS + aggregation tx time + block-ack time. */
1697 * For non-agg: frame status TX_STATUS_*
1701 * 11- 0: AGG_TX_STATE_* status code
1702 * 15-12: Retry count for 1st frame in aggregation (retries
1707 * 31-16: Sequence # for this frame's Tx cmd (not SSN!)
1718 * Reports Block-Acknowledge from recipient station
1725 /* Index of recipient (BA-sending) station in uCode's station table */
1741 u8 band; /* 0: 5 GHz, 1: 2.4 GHz */
1748 u8 band; /* 0: 5 GHz, 1: 2.4 GHz */
1755 * struct il3945_rate_scaling_cmd - Rate Scaling Command & Response
1814 * EDCA QOS access categories (as implemented by tx fifos 0-3),
1826 #define LINK_QUAL_AGG_TIME_LIMIT_DEF (4000) /* 4 milliseconds */
1847 * default set to 4000 (4 milliseconds) if not configured in .cfg
1895 * 1) If using High-throughput (HT) (SISO or MIMO) initial rate:
1930 * (attempted - success), and control the size of the win (attempted).
1939 * which rate-specific history to update, and record only those attempts that
1942 * When using block-ack (aggregation), all frames are transmitted at the same
1943 * rate, since there is no per-attempt acknowledgment from the destination
1945 * rate_n_flags field. After receiving a block-ack, the driver can update
1970 * 4) Try decreasing rate if, for current rate:
1993 * 6) Re-evaluate the rate after each tx frame. If working with block-
1996 * before re-evaluation.
2006 * For high-throughput modes (SISO or MIMO), search for new mode after:
2067 * Rate info; when using rate-scaling, Tx command's initial_rate_idx
2079 * bit 0 - 1: BT channel announcement enabled
2081 * bit 1 - 1: priority of BT device enabled
2141 u8 id; /* measurement id -- 0 or 1 */
2160 __le16 status; /* 0 - command will be handled
2161 * 1 - cannot handle (conflicts with another
2175 /* 4-5 reserved */
2199 IL_MEASURE_FRAME = (1 << 4),
2208 u8 id; /* measurement id -- 0 or 1 */
2211 u8 state; /* 0 - start, 1 - stop */
2212 __le32 start_time; /* lower 32-bits of TSF */
2213 u8 band; /* 0 - 5.2GHz, 1 - 2.4GHz */
2222 u8 basic_type; /* 0 - bss, 1 - ofdm preamble, 2 -
2226 __le32 stop_time; /* lower 32-bits of TSF */
2237 * struct il_powertable_cmd - Power Table Command
2243 * bit 0 - '0' Driver not allow power management
2247 * bit 1 - '0' Don't send sleep notification
2251 * bit 2 - '0' PM have to walk up every DTIM
2255 * bit 3 - '0' (PCI_CFG_LINK_CTRL & 0x1)
2259 * bit 4 - '1' Put radio to sleep when receiving frame for others
2262 * bit 31/30- '00' use both mac/xtal sleeps
2267 * NOTE: if sleep_interval[SLEEP_INTRVL_TBL_SIZE-1] > DTIM period then
2314 IL_PM_SLP_PHY = 4,
2351 * struct il_scan_channel - entry in C_SCAN channel table
2357 * 3) How long to stay on-channel (behavior may be modified by quiet_time,
2365 * 3) If restricting off-channel time (i.e. max_out_time !=0):
2373 * 1:4 SSID direct bit map; if a bit is set, then corresponding
2380 __le16 active_dwell; /* in 1024-uSec TU (time units), typ 5-50 */
2381 __le16 passive_dwell; /* in 1024-uSec TU (time units), typ 20-500 */
2385 #define IL39_SCAN_PROBE_MASK(n) ((BIT(n) | (BIT(n) - BIT(1))))
2399 __le16 active_dwell; /* in 1024-uSec TU (time units), typ 5-50 */
2400 __le16 passive_dwell; /* in 1024-uSec TU (time units), typ 20-500 */
2404 #define IL_SCAN_PROBE_MASK(n) cpu_to_le32((BIT(n) | (BIT(n) - BIT(1))))
2407 * struct il_ssid_ie - directed scan network information element
2409 * Up to 20 of these may appear in C_SCAN (Note: Only 4 are in
2411 * each channel may select different ssids from among the 20 (4) entries.
2420 #define PROBE_OPTION_MAX_3945 4
2439 * max_out_time is the max time off-channel (in usec), and suspend_time
2451 * 3) Sends NULL packet, with power-save (PS) bit set to 1,
2452 * to tell AP that we're going off-channel
2453 * 4) Tunes to first channel in scan list, does active or passive scan
2456 * 7) Repeats 4-6 until it no longer has time to scan the next channel
2461 * 11) Repeats entire process 2-10 until list is complete
2476 * Driver must use separate scan commands for 2.4 vs. 5 GHz bands.
2489 __le16 good_CRC_th; /* passive -> active promotion threshold */
2501 /* For active scans (set to all-0s for passive scans).
2505 /* For directed active scans (set to all-0s otherwise) */
2519 * must not mix 2.4GHz channels and 5.2GHz channels, and you must wait
2533 __le16 good_CRC_th; /* passive -> active promotion threshold */
2545 /* For active scans (set to all-0s for passive scans).
2549 /* For directed active scans (set to all-0s otherwise) */
2563 * must not mix 2.4GHz channels and 5.2GHz channels, and you must wait
2687 #define SUP_RATE_11B_MAX_NUM_CHANNELS 4
2856 * struct stats_tx_power - current tx power
2922 * count the number of times we have to re-tune
3054 * other non-associated-network source. Pertinent stats include:
3072 * Signal locks abandoned early (before phy-level header).
3075 * Signal locks abandoned late (during phy-level header).
3080 * after counting up to 2^32 - 1. Driver must differentiate vs.
3098 * by *adding* 1 to all 4 of the table entries above, up to the max for
3105 * 1). 20-beacon history of maximum background noise, indicated by
3110 * 2). 10-beacon history of strongest signal level, as indicated
3160 * "silence reference" (prev - current) is 2 or more,
3199 #define HD_AUTO_CORR40_X4_TH_ADD_MIN_MRC_IDX (4)
3231 * in from scanning, or any other non-network source).
3265 * (accum_noise[i] - accum_noise[reference]) / 30
3269 * driver should limit the difference results to a range of 0-3 (0-4.5 dB),
3275 * 1-0: amount of gain, units of 1.5 dB
3337 * The first 4 bytes of the RX frame header contain both the RX frame
3343 * 28-14: Reserved
3344 * 13-00: RX frame size