Lines Matching full:this
5 This option provides the function gpio_led_register_device.
6 As this function is used by arch code it must not be compiled as a
12 Say Y to enable Linux LED support. This allows control of supported
20 This option enables the LED sysfs class in /sys/class/leds. You'll
21 need this to do anything useful with LEDs. If unsure, say N.
27 This option enables the flash LED sysfs class in /sys/class/leds.
29 and kernel internal API to it. You'll need this to provide support
37 This option enables the multicolor LED sysfs class in /sys/class/leds.
39 and kernel internal API to it. You'll need this to provide support
40 for multicolor LEDs that are grouped together. This class is not
47 This option enables support for the brightness_hw_changed attribute
59 This option enables support for on-chip LED drivers found on Marvell
70 This option enables support for the LEDs on the AAT1290.
76 This option enables support for the AN30259A 3-channel
79 To compile this driver as a module, choose M here: the module
87 This driver makes the PC Engines APU1 front panel LEDs
93 To compile this driver as a module, choose M here: the
101 This driver adds support for controlling the front panel status
120 This option enables support for the AW2013 3-channel
123 To compile this driver as a module, choose M here: the module
132 This option enables support for LEDs connected to the BCM6328
141 This option enables support for LEDs connected to the BCM6358
150 This option enables support for LEDs offered by Motorola's
159 This option enables support for CR0014114 LED Board which
163 To compile this driver as a module, choose M here: the module
172 This option enables support for EL15203000 LED Board
176 To compile this driver as a module, choose M here: the module
186 This option enables basic support for the LEDs found on the front
195 This option enables support for the LCD backlight using
196 LM3530 ambient light sensor chip. This ALS chip can be
205 This option enables support for the LCD backlight using
206 LM3532 ambient light sensor chip. This ALS chip can be
215 This option enables support for the LEDs on National Semiconductor /
228 This option enables support for LEDs connected to LM3642.
238 This option enables support for the TI LM3692x family
247 This option enables support for the TI LM3601x family
255 This option enables support for the LEDs on Sharp Locomo.
263 This option enables support for the so called "User LED" of
271 This option enables support for on-chip LED drivers found on
279 This option enables support for LEDs connected to GPIO lines
287 This option enables support for the Soekris net4801 and net4826 error
295 This option enables support for the LEDs on the Freecom FSG-3.
302 This option enables support for the PCEngines WRAP programmable LEDs.
309 This option enables support for the front LED on Cobalt Qube series
316 This option enables support for the Cobalt Raq series LEDs.
324 This option enables support for the Left, Middle, and Right
332 Choose this option if you want to use the notification LED on
340 This option enables LED support for the handheld
348 This option enables support for NXP pca9532
367 This option enables support for the LEDs connected to GPIO
378 This option enables support for LEDs connected to the National
382 To compile this driver as a module, choose M here: the
392 This option enables support for LEDs connected to the Texas
395 To compile this driver as a module, choose M here: the
406 To compile this driver as a module, choose M here: the
418 This option supports common operations for LP5521/5523/55231/5562/8501
469 This option enables support for the Keyboard LEDs on the LP8788 PMIC.
478 This option enables support for the display cluster LEDs
487 This driver makes the mail LED accessible from userspace
488 programs through the leds subsystem. This LED have three
492 or through /sys/class/leds/clevo::mail/brightness. As this LED
497 This module can drive the mail LED for the following notebooks:
510 To compile this driver as a module, choose M here: the
518 This option enables support for LEDs connected to PCA955x
538 This option enables support for LEDs connected to the PCA963x
547 This option enables support for the status LEDs of the WM831x
555 This option enables support for LEDs driven by the Wolfson
563 This option enables support for on-chip LED drivers found
571 This option enables support for on-chip LED drivers found
579 This option enables support for DAC124S085 SPI DAC from NatSemi,
587 This option enables support for pwm driven LEDs
594 This option enables support for regulator driven LEDs.
601 This option enables support for BD2802GU RGB LED driver chips
610 This option enables support for the Intel SS4200 series of
612 drive or power LEDs on the front panel. Using this driver
621 This option enables support for LEDs driven by a Linear Technology
622 LT3593 controller. This controller uses a special one-wire pulse
630 This option enables support for on-chip LED drivers found
633 To compile this driver as a module, choose M here: the module will
641 This option enables support for on-chip LED drivers found
650 This option enables support for the dual-GPIO LEDs found on the
665 This option enables support for LEDs found on the LaCie 2Big
675 This option enables support for the LEDs on the HTC ASIC3. The HTC
677 cannot be used. This driver supports hardware blinking with an on+off
684 This option enables support for LEDs connected to TC6507
693 This option enables support for Texas Instruments TLC59108
709 This option enables support for the flash part of the MAX77693
717 This option enables support for on-chip LED drivers on
725 This option enables support for LEDs connected to LM3554
732 This option enables support for the LEDs on the Bachmann OT200.
741 This driver can also be built as a module. If so the module
749 This option enables support for KTD2692 LED flash connected
752 Say Y to enable this driver.
759 This option enables support for LEDs connected to ISSI IS31FL319x
763 This driver can also be built as a module. If so the module will be
782 This driver can also be built as a module. If so the module will be
792 This option enables support for the BlinkM RGB LED connected
801 This option enables support for the system LEDs present on
802 PowerNV platforms. Say 'y' to enable this support in kernel.
803 To compile this driver as a module, choose 'm' here: the module
812 This option enables support for the LEDs on syscon type
813 devices. This will only work with device tree enabled
821 Choose this option if you want to use the LED drivers in
829 This option enables support for the LEDs on the Mellanox
836 This option enables support for the LEDs on the Mellanox Ethernet and
838 device add call. Say Y to enable these. To compile this driver as a
845 This option enables support for userspace LEDs. Say 'y' to enable this
846 support in kernel. To compile this driver as a module, choose 'm' here:
854 This option enables support for the User1 and User2 LEDs on NI
857 To compile this driver as a module, choose M here: the module
866 This option enables support for LED controller which use a single byte
876 This supports common features between the TI LM3532, LM3631, LM3632,
885 This supports the LED device LM3697.
893 This supports the LED device LM36274.
901 This driver supports TPS61050/TPS61052 LED chips.
910 This option enables support for the Red and White LEDs of
913 To compile this driver as a module, choose M here: the module
921 This option enables support for the SGM3140 500mA Buck/Boost Charge
928 This option enables support for the Power Button LED of