Lines Matching full:lcd
20 tristate "HD44780 Character LCD support"
25 The LCD is accessible through the /dev/lcd char device (10, 156).
31 tristate "KS0108 LCD Controller"
35 If you have a LCD controlled by one or more KS0108
37 driver for your LCD.
49 hex "Parallel port where the LCD is connected"
53 The address of the parallel port where the LCD is connected.
78 If your LCD seems to miss random writings, increment this.
86 tristate "CFAG12864B LCD"
96 If you have a Crystalfontz 128x64 2-color LCD, cfag12864b Series,
97 say Y. You also need the ks0108 LCD Controller driver.
99 For help about how to wire your LCD to the parallel port,
104 The LCD framebuffer driver can be attached to a console.
118 Refresh rate of the LCD.
120 As the LCD is not memory mapped, the driver has to make the work by
126 You can freeze the computer, or the LCD maybe can't draw as fast as you
135 tristate "Imagination Technologies ASCII LCD Display"
140 Enable this to support the simple ASCII LCD displays found on
158 bool "ARM Ltd. Character LCD Driver"
161 This is a driver for the character LCD found on the ARM Ltd.
168 tristate "Parallel port LCD/Keypad Panel support"
172 Say Y here if you have an HD44780 or KS-0074 LCD connected to your
173 parallel port. This driver also features 4 and 6-key keypads. The LCD
174 is accessible through the /dev/lcd char device (10, 156), and the
188 and LCD are connected to two separate ports, you have to start two
203 1 = 2x16 parallel LCD, old keypad
204 2 = 2x16 serial LCD (KS-0074), new keypad
205 3 = 2x16 parallel LCD (Hantronix), no keypad
206 4 = 2x16 parallel LCD (Nexcom NSA1045) with Nexcom's keypad
207 5 = 2x40 parallel LCD (old one), with old keypad
232 int "LCD type (0=none, 1=custom, 2=old //, 3=ks0074, 4=hantronix, 5=Nexcom)"
236 This enables and configures an LCD connected to the parallel port.
238 '\e[L' which are specific to the LCD, and a few ANSI codes. The
240 under the name '/dev/lcd'. There are a total of 6 supported types :
244 2 : 2x16 & 2x40 parallel LCD (old wiring)
245 3 : 2x16 serial LCD (KS-0074 based)
246 4 : 2x16 parallel LCD (Hantronix wiring)
247 5 : 2x16 parallel LCD (Nexcom wiring)
255 int "Number of lines on the LCD (1-2)"
259 This is the number of visible character lines on the LCD in custom profile.
264 int "Number of characters per line on the LCD (1-40)"
268 This is the number of characters per line on the LCD in custom profile.
273 int "Internal LCD line width (1-40, 40 by default)"
284 This option lets you configure the value used by your LCD in 'custom' profile.
289 int "Hardware LCD line width (1-64, 64 by default)"
298 If you don't know what your LCD uses, in doubt let 16 here for a 2x16, and
303 int "LCD character set (0=normal, 1=KS0074)"
319 int "LCD communication mode (0=parallel 8 bits, 1=serial)"
323 This driver now supports any serial or parallel LCD wired to a parallel
325 be driving a serial LCD or a parallel one. Serial LCDs only use 2 wires
328 parallel LCD, and 1 for a serial LCD.
332 int "Parallel port pin number & polarity connected to the LCD E signal (-17...17) "
336 This describes the number of the parallel port pin to which the LCD 'E'
347 int "Parallel port pin number & polarity connected to the LCD RS signal (-17...17) "
351 This describes the number of the parallel port pin to which the LCD 'RS'
362 int "Parallel port pin number & polarity connected to the LCD RW signal (-17...17) "
366 This describes the number of the parallel port pin to which the LCD 'RW'
377 int "Parallel port pin number & polarity connected to the LCD SCL signal (-17...17) "
382 LCD 'SCL' signal has been connected. It can be :
392 int "Parallel port pin number & polarity connected to the LCD SDA signal (-17...17) "
397 LCD 'SDA' signal has been connected. It can be :
407 int "Parallel port pin number & polarity connected to the LCD backlight signal (-17...17) "
411 This describes the number of the parallel port pin to which the LCD 'BL' signal
423 bool "Change LCD initialization message ?"
477 tristate "Parallel port LCD/Keypad Panel support (OLD OPTION)"
483 tristate "Character LCD core support" if COMPILE_TEST