40 #define DB1300_IDE_INT		(DB1300_FIRST_INT + 0)
58 #define DB1300_ETH_PHYS_ADDR	0x19000000
59 #define DB1300_ETH_PHYS_END	0x197fffff
62 #define DB1300_IDE_PHYS_ADDR	0x18800000
67 #define DB1300_NAND_PHYS_ADDR	0x20000000
68 #define DB1300_NAND_PHYS_END	0x20000fff
72 	{ I2C_BOARD_INFO("wm8731", 0x1b), },	/* I2S audio codec */
73 	{ I2C_BOARD_INFO("ne1619", 0x2d), },	/* adm1025-compat hwmon */
86 	/* wake-from-str pins 0-3 */
138 	i = &db1300_dev_pins[0];  in db1300_gpio_config()
142 	i = &db1300_gpio_pins[0];  in db1300_gpio_config()
158 	ioaddr &= 0xffffff00;  in au1300_nand_cmd_ctrl()
182 		.name	= "NAND FS 0",
183 		.offset = 0,
196 		.chip_offset	= 0,
208 	[0] = {
210 		.end	= DB1300_NAND_PHYS_ADDR + 0xff,
228 	[0] = {
260 	[0] = {
262 		.end	= AU1300_PSC1_PHYS_ADDR + 0x0fff,
292 	[0] = {
294 		.end	= AU1300_PSC2_PHYS_ADDR + 0x0fff,
324 	[0] = {
326 		.end	= AU1300_PSC3_PHYS_ADDR + 0x0fff,
348 	.id		= 0,	/* bus number */
424 	[0] = {
497 				db1300_mmc_cdfn, 0, "sd_insert", mmc_host);  in db1300_mmc_cd_setup()
502 				db1300_mmc_cdfn, 0, "sd_eject", mmc_host);  in db1300_mmc_cd_setup()
517 	ret = 0;  in db1300_mmc_cd_setup()
526 		bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);  in db1300_mmcled_set()
528 		bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);  in db1300_mmcled_set()
543 	[0] = {
581 	return 0; /* disable for now, it doesn't work yet */  in db1300_movinand_inserted()
586 	return 0;  in db1300_movinand_readonly()
593 		bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED1, 0);  in db1300_movinand_led_set()
595 		bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED1);  in db1300_movinand_led_set()
610 	[0] = {
639 	.id		= 0,
689 	return 0;  in db1300fb_panel_init()
697 	return 0;  in db1300fb_panel_shutdown()
707 	[0] = {
709 		.end	= AU1200_LCD_PHYS_ADDR + 0x800 - 1,
722 	.id		= 0,
820 	prom_get_ethernet_addr(&db1300_eth_config.mac[0]);  in db1300_dev_setup()
822 	i2c_register_board_info(0, db1300_i2c_devs,  in db1300_dev_setup()
847 	bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_USBHPWR | BCSR_RESETS_OTGPWR);  in db1300_dev_setup()
849 	/* although it is socket #0, it uses the CPLD bits which previous boards  in db1300_dev_setup()
854 		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x00400000 - 1,  in db1300_dev_setup()
856 		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x00400000 - 1,  in db1300_dev_setup()
858 		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x00010000 - 1,  in db1300_dev_setup()
859 		DB1300_CF_INT, DB1300_CF_INSERT_INT, 0, DB1300_CF_EJECT_INT, 1);  in db1300_dev_setup()
891 	return 0;  in db1300_board_setup()