Lines Matching +full:charge +full:- +full:ctrl +full:- +full:value
1 // SPDX-License-Identifier: BSD-3-Clause
8 /dts-v1/;
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
18 compatible = "qcom,sc7180-idp", "qcom,sc7180";
28 stdout-path = "serial0:115200n8";
40 /delete-node/ &hyp_mem;
41 /delete-node/ &xbl_mem;
42 /delete-node/ &aop_mem;
43 /delete-node/ &sec_apps_mem;
44 /delete-node/ &tz_mem;
52 reserved-memory {
55 no-map;
60 no-map;
65 no-map;
70 no-map;
75 no-map;
80 no-map;
86 pm6150-rpmh-regulators {
87 compatible = "qcom,pm6150-rpmh-regulators";
88 qcom,pmic-id = "a";
91 regulator-min-microvolt = <1128000>;
92 regulator-max-microvolt = <1128000>;
96 regulator-min-microvolt = <824000>;
97 regulator-max-microvolt = <1120000>;
101 regulator-min-microvolt = <1744000>;
102 regulator-max-microvolt = <2040000>;
106 regulator-min-microvolt = <1178000>;
107 regulator-max-microvolt = <1256000>;
108 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
112 regulator-min-microvolt = <944000>;
113 regulator-max-microvolt = <1056000>;
114 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
118 regulator-min-microvolt = <968000>;
119 regulator-max-microvolt = <1064000>;
120 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
124 regulator-min-microvolt = <824000>;
125 regulator-max-microvolt = <928000>;
126 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
130 regulator-min-microvolt = <2496000>;
131 regulator-max-microvolt = <3000000>;
132 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
136 regulator-min-microvolt = <568000>;
137 regulator-max-microvolt = <648000>;
138 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
142 regulator-min-microvolt = <488000>;
143 regulator-max-microvolt = <800000>;
144 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
148 regulator-min-microvolt = <1800000>;
149 regulator-max-microvolt = <1832000>;
150 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
154 regulator-min-microvolt = <1696000>;
155 regulator-max-microvolt = <1904000>;
156 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
160 regulator-min-microvolt = <1800000>;
161 regulator-max-microvolt = <1800000>;
162 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
166 regulator-min-microvolt = <1696000>;
167 regulator-max-microvolt = <1904000>;
168 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
172 regulator-min-microvolt = <1728000>;
173 regulator-max-microvolt = <1832000>;
174 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
178 regulator-min-microvolt = <1696000>;
179 regulator-max-microvolt = <1904000>;
180 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
184 regulator-min-microvolt = <2496000>;
185 regulator-max-microvolt = <3304000>;
186 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
190 regulator-min-microvolt = <2920000>;
191 regulator-max-microvolt = <3232000>;
192 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
196 regulator-min-microvolt = <2496000>;
197 regulator-max-microvolt = <3304000>;
198 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
202 regulator-min-microvolt = <2960000>;
203 regulator-max-microvolt = <2960000>;
204 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
208 pm6150l-rpmh-regulators {
209 compatible = "qcom,pm6150l-rpmh-regulators";
210 qcom,pmic-id = "c";
213 regulator-min-microvolt = <1120000>;
214 regulator-max-microvolt = <1408000>;
218 regulator-min-microvolt = <1616000>;
219 regulator-max-microvolt = <1984000>;
220 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
224 regulator-min-microvolt = <1168000>;
225 regulator-max-microvolt = <1304000>;
226 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
230 regulator-min-microvolt = <1144000>;
231 regulator-max-microvolt = <1304000>;
232 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
236 regulator-min-microvolt = <1648000>;
237 regulator-max-microvolt = <3304000>;
238 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
242 regulator-min-microvolt = <1648000>;
243 regulator-max-microvolt = <3304000>;
244 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
248 regulator-min-microvolt = <1800000>;
249 regulator-max-microvolt = <2950000>;
250 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
254 regulator-min-microvolt = <3000000>;
255 regulator-max-microvolt = <3312000>;
256 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
260 regulator-min-microvolt = <1800000>;
261 regulator-max-microvolt = <1904000>;
262 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
266 regulator-min-microvolt = <2960000>;
267 regulator-max-microvolt = <2960000>;
268 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
272 regulator-min-microvolt = <3000000>;
273 regulator-max-microvolt = <3400000>;
274 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
278 regulator-min-microvolt = <3000000>;
279 regulator-max-microvolt = <3400000>;
280 regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
284 regulator-min-microvolt = <3008000>;
285 regulator-max-microvolt = <3960000>;
286 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
292 vcc-supply = <&vreg_l11a_1p8>;
297 pinctrl-names = "default";
298 pinctrl-0 = <&qspi_clk &qspi_cs0 &qspi_data01>;
301 compatible = "jedec,spi-nor";
303 spi-max-frequency = <25000000>;
304 spi-tx-bus-width = <2>;
305 spi-rx-bus-width = <2>;
319 compatible = "qcom,sc7180-mss-pil";
321 memory-region = <&mba_mem &mpss_mem>;
327 pinctrl-names = "default", "sleep";
328 pinctrl-0 = <&sdc1_on>;
329 pinctrl-1 = <&sdc1_off>;
330 vmmc-supply = <&vreg_l19a_2p9>;
331 vqmmc-supply = <&vreg_l12a_1p8>;
337 pinctrl-names = "default","sleep";
338 pinctrl-0 = <&sdc2_on>;
339 pinctrl-1 = <&sdc2_off>;
340 vmmc-supply = <&vreg_l9c_2p9>;
341 vqmmc-supply = <&vreg_l6c_2p9>;
343 cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>;
349 /delete-property/interrupts;
350 interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
353 pinctrl-names = "default", "sleep";
354 pinctrl-1 = <&qup_uart3_sleep>;
356 bluetooth: wcn3990-bt {
357 compatible = "qcom,wcn3990-bt";
358 vddio-supply = <&vreg_l10a_1p8>;
359 vddxo-supply = <&vreg_l1c_1p8>;
360 vddrf-supply = <&vreg_l2c_1p3>;
361 vddch0-supply = <&vreg_l10c_3p3>;
362 max-speed = <3200000>;
380 vdd-supply = <&vreg_l4a_0p8>;
381 vdda-pll-supply = <&vreg_l11a_1p8>;
382 vdda-phy-dpdm-supply = <&vreg_l17a_3p0>;
383 qcom,imp-res-offset-value = <8>;
384 qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>;
385 qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
386 qcom,bias-ctrl-value = <0x22>;
387 qcom,charge-ctrl-value = <3>;
388 qcom,hsdisc-trim-value = <0>;
393 vdda-phy-supply = <&vreg_l3c_1p2>;
394 vdda-pll-supply = <&vreg_l4a_0p8>;
398 video-firmware {
405 vdd-0.8-cx-mx-supply = <&vreg_l9a_0p6>;
406 vdd-1.8-xo-supply = <&vreg_l1c_1p8>;
407 vdd-1.3-rfa-supply = <&vreg_l2c_1p3>;
408 vdd-3.3-ch0-supply = <&vreg_l10c_3p3>;
409 vdd-3.3-ch1-supply = <&vreg_l11c_3p3>;
410 wifi-firmware {
415 /* PINCTRL - additions to nodes defined in sc7180.dtsi */
420 bias-disable;
427 bias-disable;
435 /* High-Z when no transfers; nice to park the lines */
436 bias-pull-up;
443 drive-strength = <2>;
446 bias-disable;
453 drive-strength = <2>;
456 bias-disable;
463 drive-strength = <2>;
466 bias-disable;
473 drive-strength = <2>;
476 bias-disable;
481 pinconf-cts {
483 * Configure a pull-down on CTS to match the pull of
487 bias-pull-down;
490 pinconf-rts {
493 drive-strength = <2>;
494 bias-disable;
497 pinconf-tx {
500 drive-strength = <2>;
501 bias-disable;
504 pinconf-rx {
506 * Configure a pull-up on RX. This is needed to avoid
508 * in tri-state (module powered off or not driving the
512 bias-pull-up;
517 pinconf-tx {
519 drive-strength = <2>;
520 bias-disable;
523 pinconf-rx {
525 drive-strength = <2>;
526 bias-pull-up;
533 drive-strength = <2>;
534 bias-disable;
541 drive-strength = <2>;
542 bias-disable;
549 drive-strength = <2>;
550 bias-disable;
555 qup_uart3_sleep: qup-uart3-sleep {
562 pinconf-cts {
564 * Configure a pull-down on CTS to match the pull of
568 bias-pull-down;
571 pinconf-rts {
573 * Configure pull-down on RTS. As RTS is active low
579 bias-pull-down;
582 pinconf-tx {
584 * Configure pull-up on TX when it isn't actively driven
588 bias-pull-up;
591 pinconf-rx {
593 * Configure a pull-up on RX. This is needed to avoid
598 bias-pull-up;