Lines Matching +full:vdd +full:- +full:supply
1 // SPDX-License-Identifier: GPL-2.0
4 #include <dt-bindings/gpio/gpio.h>
7 #include <dt-bindings/gpio/gpio.h>
8 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
17 stdout-path = "serial0";
20 vph_pwr: vph-pwr-regulator {
21 compatible = "regulator-fixed";
22 regulator-name = "vph_pwr";
23 regulator-always-on;
24 regulator-boot-on;
28 vdd_esmps3_3p3: vdd-esmps3-3p3-regulator {
29 compatible = "regulator-fixed";
30 regulator-name = "eSMPS3_3P3";
32 regulator-min-microvolt = <3300000>;
33 regulator-max-microvolt = <3300000>;
34 regulator-always-on;
37 usb3_vbus_reg: regulator-usb3-vbus {
38 compatible = "regulator-fixed";
39 regulator-name = "VBUS_BOOST_5V";
40 regulator-min-microvolt = <5000000>;
41 regulator-max-microvolt = <5000000>;
43 pinctrl-names = "default";
44 pinctrl-0 = <&usb_vbus_boost_pin>;
45 vin-supply = <&vph_pwr>;
46 enable-active-high;
49 regulator-always-on;
57 compatible = "qcom,wcn3990-bt";
58 vddio-supply = <&vreg_l6_1p8>;
59 vddxo-supply = <&vreg_l5_1p8>;
60 vddrf-supply = <&vreg_l1_1p3>;
61 vddch0-supply = <&vdd_ch0_3p3>;
63 local-bd-address = [ 02 00 00 00 5a ad ];
65 max-speed = <3200000>;
70 qcom,controlled-remotely;
74 qcom,controlled-remotely;
78 protected-clocks = <GCC_BIMC_CDSP_CLK>,
87 vdd_s3-supply = <&vph_pwr>;
90 regulator-always-on;
91 regulator-boot-on;
92 regulator-name = "vdd_apc";
93 regulator-initial-mode = <1>;
94 regulator-min-microvolt = <1048000>;
95 regulator-max-microvolt = <1384000>;
102 perst-gpio = <&tlmm 43 GPIO_ACTIVE_LOW>;
104 pinctrl-names = "default";
105 pinctrl-0 = <&perst_state>;
111 vdda-vp-supply = <&vreg_l3_1p05>;
112 vdda-vph-supply = <&vreg_l5_1p8>;
128 pms405-regulators {
129 compatible = "qcom,rpm-pms405-regulators";
131 vdd_s1-supply = <&vph_pwr>;
132 vdd_s2-supply = <&vph_pwr>;
133 vdd_s3-supply = <&vph_pwr>;
134 vdd_s4-supply = <&vph_pwr>;
135 vdd_s5-supply = <&vph_pwr>;
136 vdd_l1_l2-supply = <&vreg_s5_1p35>;
137 vdd_l3_l8-supply = <&vreg_s5_1p35>;
138 vdd_l4-supply = <&vreg_s5_1p35>;
139 vdd_l5_l6-supply = <&vreg_s4_1p8>;
140 vdd_l7-supply = <&vph_pwr>;
141 vdd_l9-supply = <&vreg_s5_1p35>;
142 vdd_l10_l11_l12_l13-supply = <&vph_pwr>;
145 regulator-min-microvolt = <1728000>;
146 regulator-max-microvolt = <1920000>;
150 regulator-min-microvolt = <1352000>;
151 regulator-max-microvolt = <1352000>;
155 regulator-min-microvolt = <1240000>;
156 regulator-max-microvolt = <1352000>;
160 regulator-min-microvolt = <1048000>;
161 regulator-max-microvolt = <1280000>;
165 regulator-min-microvolt = <1048000>;
166 regulator-max-microvolt = <1160000>;
170 regulator-min-microvolt = <1144000>;
171 regulator-max-microvolt = <1256000>;
175 regulator-min-microvolt = <1800000>;
176 regulator-max-microvolt = <1800000>;
180 regulator-min-microvolt = <1800000>;
181 regulator-max-microvolt = <1800000>;
182 regulator-always-on;
186 regulator-min-microvolt = <1616000>;
187 regulator-max-microvolt = <3000000>;
191 regulator-min-microvolt = <1136000>;
192 regulator-max-microvolt = <1352000>;
196 regulator-min-microvolt = <2936000>;
197 regulator-max-microvolt = <3088000>;
201 regulator-min-microvolt = <2696000>;
202 regulator-max-microvolt = <3304000>;
206 regulator-min-microvolt = <3050000>;
207 regulator-max-microvolt = <3300000>;
211 regulator-min-microvolt = <3000000>;
212 regulator-max-microvolt = <3300000>;
220 supports-cqe;
221 mmc-ddr-1_8v;
222 mmc-hs400-1_8v;
223 bus-width = <8>;
224 non-removable;
226 pinctrl-names = "default", "sleep";
227 pinctrl-0 = <&sdc1_on>;
228 pinctrl-1 = <&sdc1_off>;
236 drive-strength = <2>;
237 bias-disable;
238 output-low;
241 sdc1_on: sdc1-on {
244 bias-disable;
245 drive-strength = <16>;
250 bias-pull-up;
251 drive-strength = <10>;
256 bias-pull-up;
257 drive-strength = <10>;
262 bias-pull-down;
266 sdc1_off: sdc1-off {
269 bias-disable;
270 drive-strength = <2>;
275 bias-pull-up;
276 drive-strength = <2>;
281 bias-pull-up;
282 drive-strength = <2>;
287 bias-pull-down;
291 usb3_id_pin: usb3-id-pin {
299 drive-strength = <2>;
300 bias-pull-up;
301 input-enable;
307 usb_vbus_boost_pin: usb-vbus-boost-pin {
311 output-low;
312 power-source = <1>;
315 usb3_vbus_pin: usb3-vbus-pin {
319 input-enable;
320 bias-pull-down;
321 power-source = <1>;
331 vdd-supply = <&vreg_l4_1p2>;
332 vdda1p8-supply = <&vreg_l5_1p8>;
333 vdda3p3-supply = <&vreg_l12_3p3>;
346 vdd-supply = <&vreg_l4_1p2>;
347 vdda1p8-supply = <&vreg_l5_1p8>;
348 vdda3p3-supply = <&vreg_l12_3p3>;
353 vdd-supply = <&vreg_l3_1p05>;
354 vdda1p8-supply = <&vreg_l5_1p8>;
360 vdd-0.8-cx-mx-supply = <&vreg_l2_1p275>;
361 vdd-1.8-xo-supply = <&vreg_l5_1p8>;
362 vdd-1.3-rfa-supply = <&vreg_l1_1p3>;
365 /* PINCTRL - additions to nodes defined in qcs404.dtsi */
369 drive-strength = <2>;
370 bias-disable;
374 drive-strength = <2>;
375 bias-disable;
382 bias-disable;
385 rts-tx {
387 drive-strength = <2>;
388 bias-disable;
393 bias-pull-up;