Lines Matching +full:opp +full:- +full:100000000
1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
8 compatible = "mmc-pwrseq-simple";
9 pinctrl-names = "default";
10 pinctrl-0 = <&pinctrl_usdhc1_gpio>;
11 reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
13 clock-names = "ext_clock";
14 post-power-on-delay-ms = <80>;
24 cpu-supply = <&buck2_reg>;
28 operating-points-v2 = <&ddrc_opp_table>;
30 ddrc_opp_table: opp-table {
31 compatible = "operating-points-v2";
33 opp-25M {
34 opp-hz = /bits/ 64 <25000000>;
37 opp-100M {
38 opp-hz = /bits/ 64 <100000000>;
41 opp-750M {
42 opp-hz = /bits/ 64 <750000000>;
48 pinctrl-names = "default";
49 pinctrl-0 = <&pinctrl_fec1>;
50 phy-mode = "rgmii-id";
51 phy-handle = <ðphy0>;
52 fsl,magic-packet;
56 #address-cells = <1>;
57 #size-cells = <0>;
59 ethphy0: ethernet-phy@0 {
60 compatible = "ethernet-phy-ieee802.3-c22";
67 clock-frequency = <400000>;
68 pinctrl-names = "default";
69 pinctrl-0 = <&pinctrl_i2c1>;
75 pinctrl-names = "default";
76 pinctrl-0 = <&pinctrl_pmic>;
77 interrupt-parent = <&gpio1>;
79 rohm,reset-snvs-powered;
83 regulator-name = "buck1";
84 regulator-min-microvolt = <700000>;
85 regulator-max-microvolt = <1300000>;
86 regulator-boot-on;
87 regulator-always-on;
88 regulator-ramp-delay = <1250>;
92 regulator-name = "buck2";
93 regulator-min-microvolt = <700000>;
94 regulator-max-microvolt = <1300000>;
95 regulator-boot-on;
96 regulator-always-on;
97 regulator-ramp-delay = <1250>;
98 rohm,dvs-run-voltage = <1000000>;
99 rohm,dvs-idle-voltage = <900000>;
104 regulator-name = "buck3";
105 regulator-min-microvolt = <700000>;
106 regulator-max-microvolt = <1350000>;
107 regulator-boot-on;
108 regulator-always-on;
113 regulator-name = "buck4";
114 regulator-min-microvolt = <3000000>;
115 regulator-max-microvolt = <3300000>;
116 regulator-boot-on;
117 regulator-always-on;
122 regulator-name = "buck5";
123 regulator-min-microvolt = <1605000>;
124 regulator-max-microvolt = <1995000>;
125 regulator-boot-on;
126 regulator-always-on;
131 regulator-name = "buck6";
132 regulator-min-microvolt = <800000>;
133 regulator-max-microvolt = <1400000>;
134 regulator-boot-on;
135 regulator-always-on;
139 regulator-name = "ldo1";
140 regulator-min-microvolt = <1600000>;
141 regulator-max-microvolt = <3300000>;
142 regulator-boot-on;
143 regulator-always-on;
147 regulator-name = "ldo2";
148 regulator-min-microvolt = <800000>;
149 regulator-max-microvolt = <900000>;
150 regulator-boot-on;
151 regulator-always-on;
155 regulator-name = "ldo3";
156 regulator-min-microvolt = <1800000>;
157 regulator-max-microvolt = <3300000>;
158 regulator-boot-on;
159 regulator-always-on;
163 regulator-name = "ldo4";
164 regulator-min-microvolt = <900000>;
165 regulator-max-microvolt = <1800000>;
166 regulator-boot-on;
167 regulator-always-on;
171 regulator-name = "ldo6";
172 regulator-min-microvolt = <900000>;
173 regulator-max-microvolt = <1800000>;
174 regulator-boot-on;
175 regulator-always-on;
182 clock-frequency = <400000>;
183 pinctrl-names = "default";
184 pinctrl-0 = <&pinctrl_i2c3>;
190 read-only; /* Manufacturing EEPROM programmed at factory */
201 pinctrl-names = "default";
202 pinctrl-0 = <&pinctrl_uart1>;
203 assigned-clocks = <&clk IMX8MM_CLK_UART1>;
204 assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
205 uart-has-rtscts;
209 compatible = "brcm,bcm43438-bt";
210 shutdown-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
211 host-wakeup-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
212 device-wakeup-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
214 max-speed = <4000000>;
215 clock-names = "extclk";
220 #address-cells = <1>;
221 #size-cells = <0>;
222 pinctrl-names = "default";
223 pinctrl-0 = <&pinctrl_usdhc1>;
224 bus-width = <4>;
225 non-removable;
226 cap-power-off-card;
227 pm-ignore-notify;
228 keep-power-in-suspend;
229 mmc-pwrseq = <&usdhc1_pwrseq>;
234 compatible = "brcm,bcm4329-fmac";
235 pinctrl-names = "default";
236 pinctrl-0 = <&pinctrl_wlan>;
237 interrupt-parent = <&gpio2>;
239 interrupt-names = "host-wake";
244 pinctrl-names = "default", "state_100mhz", "state_200mhz";
245 pinctrl-0 = <&pinctrl_usdhc3>;
246 pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
247 pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
248 bus-width = <8>;
249 non-removable;
254 pinctrl-names = "default";
255 pinctrl-0 = <&pinctrl_wdog>;
256 fsl,ext-reset-output;
331 pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
342 pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
369 pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
385 pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {