Lines Matching +full:sda +full:- +full:gpios
1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
8 /dts-v1/;
10 #include "meson-gxbb.dtsi"
11 #include <dt-bindings/gpio/gpio.h>
14 compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
15 model = "Hardkernel ODROID-C2";
23 stdout-path = "serial0:115200n8";
31 usb_otg_pwr: regulator-usb-pwrs {
32 compatible = "regulator-fixed";
34 regulator-name = "USB_OTG_PWR";
36 regulator-min-microvolt = <5000000>;
37 regulator-max-microvolt = <5000000>;
43 enable-active-high;
47 vin-supply = <&p5v0>;
51 compatible = "gpio-leds";
52 led-blue {
54 gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>;
55 linux,default-trigger = "heartbeat";
56 default-state = "off";
60 p5v0: regulator-p5v0 {
61 compatible = "regulator-fixed";
63 regulator-name = "P5V0";
64 regulator-min-microvolt = <5000000>;
65 regulator-max-microvolt = <5000000>;
66 regulator-always-on;
69 hdmi_p5v0: regulator-hdmi_p5v0 {
70 compatible = "regulator-fixed";
71 regulator-name = "HDMI_P5V0";
72 regulator-min-microvolt = <5000000>;
73 regulator-max-microvolt = <5000000>;
74 /* AP2331SA-7 */
75 vin-supply = <&p5v0>;
78 tflash_vdd: regulator-tflash_vdd {
79 compatible = "regulator-fixed";
81 regulator-name = "TFLASH_VDD";
82 regulator-min-microvolt = <3300000>;
83 regulator-max-microvolt = <3300000>;
89 enable-active-high;
91 vin-supply = <&vddio_ao3v3>;
94 tf_io: gpio-regulator-tf_io {
95 compatible = "regulator-gpio";
97 regulator-name = "TF_IO";
98 regulator-min-microvolt = <1800000>;
99 regulator-max-microvolt = <3300000>;
104 gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
105 gpios-states = <0>;
110 vin-supply = <&vddio_ao3v3>;
113 vcc1v8: regulator-vcc1v8 {
114 compatible = "regulator-fixed";
115 regulator-name = "VCC1V8";
116 regulator-min-microvolt = <1800000>;
117 regulator-max-microvolt = <1800000>;
118 regulator-always-on;
120 vin-supply = <&vddio_ao3v3>;
123 vcc3v3: regulator-vcc3v3 {
124 compatible = "regulator-fixed";
125 regulator-name = "VCC3V3";
126 regulator-min-microvolt = <3300000>;
127 regulator-max-microvolt = <3300000>;
130 vddio_ao1v8: regulator-vddio-ao1v8 {
131 compatible = "regulator-fixed";
132 regulator-name = "VDDIO_AO1V8";
133 regulator-min-microvolt = <1800000>;
134 regulator-max-microvolt = <1800000>;
135 regulator-always-on;
137 vin-supply = <&p5v0>;
140 vddio_ao3v3: regulator-vddio-ao3v3 {
141 compatible = "regulator-fixed";
142 regulator-name = "VDDIO_AO3V3";
143 regulator-min-microvolt = <3300000>;
144 regulator-max-microvolt = <3300000>;
145 regulator-always-on;
146 /* U11 MP2161GJ-C499 */
147 vin-supply = <&p5v0>;
150 ddr3_1v5: regulator-ddr3_1v5 {
151 compatible = "regulator-fixed";
152 regulator-name = "DDR3_1V5";
153 regulator-min-microvolt = <1500000>;
154 regulator-max-microvolt = <1500000>;
155 regulator-always-on;
156 /* U15 MP2161GJ-C499 */
157 vin-supply = <&p5v0>;
160 emmc_pwrseq: emmc-pwrseq {
161 compatible = "mmc-pwrseq-emmc";
162 reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
165 hdmi-connector {
166 compatible = "hdmi-connector";
171 remote-endpoint = <&hdmi_tx_tmds_out>;
179 pinctrl-0 = <&ao_cec_pins>;
180 pinctrl-names = "default";
181 hdmi-phandle = <&hdmi_tx>;
186 pinctrl-0 = <ð_rgmii_pins>;
187 pinctrl-names = "default";
188 phy-handle = <ð_phy0>;
189 phy-mode = "rgmii";
191 amlogic,tx-delay-ns = <2>;
194 compatible = "snps,dwmac-mdio";
195 #address-cells = <1>;
196 #size-cells = <0>;
198 eth_phy0: ethernet-phy@0 {
202 reset-assert-us = <10000>;
203 reset-deassert-us = <30000>;
204 reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
206 interrupt-parent = <&gpio_intc>;
215 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
220 usb-hub {
221 gpio-hog;
222 gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
223 output-high;
224 line-name = "usb-hub-reset";
230 pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
231 pinctrl-names = "default";
232 hdmi-supply = <&hdmi_p5v0>;
237 remote-endpoint = <&hdmi_connector_in>;
243 pinctrl-0 = <&i2c_a_pins>;
244 pinctrl-names = "default";
249 pinctrl-0 = <&remote_input_ao_pins>;
250 pinctrl-names = "default";
251 linux,rc-map-name = "rc-odroid";
255 gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
265 gpio-line-names = /* Bank GPIOZ */
272 "HDMI HPD", "HDMI DDC SDA", "HDMI DDC SCL", "",
284 "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK",
307 vref-supply = <&vcc1v8>;
317 pinctrl-0 = <&sdcard_pins>;
318 pinctrl-1 = <&sdcard_clk_gate_pins>;
319 pinctrl-names = "default", "clk-gate";
321 bus-width = <4>;
322 cap-sd-highspeed;
323 sd-uhs-sdr12;
324 sd-uhs-sdr25;
325 sd-uhs-sdr50;
326 sd-uhs-ddr50;
327 max-frequency = <100000000>;
328 disable-wp;
330 cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
332 vmmc-supply = <&tflash_vdd>;
333 vqmmc-supply = <&tf_io>;
339 pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
340 pinctrl-1 = <&emmc_clk_gate_pins>;
341 pinctrl-names = "default", "clk-gate";
343 bus-width = <8>;
344 max-frequency = <200000000>;
345 non-removable;
346 disable-wp;
347 cap-mmc-highspeed;
348 mmc-ddr-1_8v;
349 mmc-hs200-1_8v;
351 mmc-pwrseq = <&emmc_pwrseq>;
352 vmmc-supply = <&vcc3v3>;
353 vqmmc-supply = <&vcc1v8>;
358 pinctrl-0 = <&uart_ao_a_pins>;
359 pinctrl-names = "default";
364 phy-supply = <&usb_otg_pwr>;
369 phy-supply = <&usb_otg_pwr>;