Lines Matching +full:gpios +full:- +full:states

1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
5  * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
6  *   Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
9 /dts-v1/;
10 #include "sun8i-h3.dtsi"
11 #include "sunxi-common-regulators.dtsi"
13 #include <dt-bindings/gpio/gpio.h>
14 #include <dt-bindings/input/input.h>
17 	model = "Banana Pi BPI-M2-Zero";
18 	compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus";
26 		stdout-path = "serial0:115200n8";
30 		compatible = "gpio-leds";
33 			label = "bananapi-m2-zero:red:pwr";
34 			gpios = <&r_pio 0 10 GPIO_ACTIVE_LOW>; /* PL10 */
35 			default-state = "on";
40 		compatible = "gpio-keys";
45 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
49 	reg_vdd_cpux: vdd-cpux-regulator {
50 		compatible = "regulator-gpio";
51 		regulator-name = "vdd-cpux";
52 		regulator-type = "voltage";
53 		regulator-boot-on;
54 		regulator-always-on;
55 		regulator-min-microvolt = <1100000>;
56 		regulator-max-microvolt = <1300000>;
57 		regulator-ramp-delay = <50>; /* 4ms */
59 		gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
60 		enable-active-high;
61 		gpios-states = <0x1>;
62 		states = <1100000 0>, <1300000 1>;
66 		compatible = "mmc-pwrseq-simple";
67 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
69 		clock-names = "ext_clock";
74 	cpu-supply = <&reg_vdd_cpux>;
82 	vmmc-supply = <&reg_vcc3v3>;
83 	bus-width = <4>;
89 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
94 	vmmc-supply = <&reg_vcc3v3>;
95 	vqmmc-supply = <&reg_vcc3v3>;
96 	mmc-pwrseq = <&wifi_pwrseq>;
97 	bus-width = <4>;
98 	non-removable;
103 		compatible = "brcm,bcm4329-fmac";
104 		interrupt-parent = <&pio>;
106 		interrupt-names = "host-wake";
115 	pinctrl-names = "default";
116 	pinctrl-0 = <&uart0_pa_pins>;
121 	pinctrl-names = "default";
122 	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
123 	uart-has-rtscts;
127 		compatible = "brcm,bcm43438-bt";
129 		clock-names = "lpo";
130 		vbat-supply = <&reg_vcc3v3>;
131 		vddio-supply = <&reg_vcc3v3>;
132 		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
133 		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
134 		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
145 	usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
147 	 * There're two micro-USB connectors, one is power-only and another is
150 	 * from the power-only USB port.