Lines Matching +full:charge +full:- +full:status +full:- +full:gpios

5  * This file is dual-licensed: you can use it either under the terms
22  *  b) Permission is hereby granted, free of charge, to any person
44 /dts-v1/;
45 #include "sun7i-a20.dtsi"
46 #include "sunxi-common-regulators.dtsi"
48 #include <dt-bindings/gpio/gpio.h>
49 #include <dt-bindings/input/input.h>
50 #include <dt-bindings/interrupt-controller/irq.h>
51 #include <dt-bindings/pwm/pwm.h>
55 	compatible = "wexler,tab7200", "allwinner,sun7i-a20";
62 		compatible = "pwm-backlight";
64 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
65 		default-brightness-level = <8>;
66 		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
70 		stdout-path = "serial0:115200n8";
75 	allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
76 	status = "okay";
80 	cpu-supply = <&reg_dcdc2>;
84 	status = "okay";
88 	status = "okay";
92 	status = "okay";
96 		interrupt-parent = <&nmi_intc>;
104 	status = "okay";
108 	status = "okay";
113 		interrupt-parent = <&pio>;
115 		irq-gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* INT (PH21) */
116 		reset-gpios = <&pio 1 13 GPIO_ACTIVE_HIGH>; /* RST (PB13) */
117 		touchscreen-swapped-x-y;
122 	vref-supply = <&reg_vcc3v0>;
123 	status = "okay";
125 	button-571 {
132 	button-761 {
141 	vmmc-supply = <&reg_vcc3v3>;
142 	bus-width = <4>;
143 	cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
144 	status = "okay";
148 	status = "okay";
152 	status = "okay";
156 	status = "okay";
160 	pinctrl-names = "default";
161 	pinctrl-0 = <&pwm0_pin>;
162 	status = "okay";
166 	regulator-always-on;
167 	regulator-min-microvolt = <1000000>;
168 	regulator-max-microvolt = <1450000>;
169 	regulator-name = "vdd-cpu";
173 	regulator-always-on;
174 	regulator-min-microvolt = <1000000>;
175 	regulator-max-microvolt = <1400000>;
176 	regulator-name = "vdd-int-dll";
180 	regulator-name = "vdd-rtc";
184 	regulator-always-on;
185 	regulator-min-microvolt = <3000000>;
186 	regulator-max-microvolt = <3000000>;
187 	regulator-name = "avcc";
191 	status = "okay";
195 	status = "okay";
199 	status = "okay";
203 	pinctrl-names = "default";
204 	pinctrl-0 = <&uart0_pb_pins>;
205 	status = "okay";
210 	status = "okay";
214 	status = "okay";
218 	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
219 	usb0_vbus_power-supply = <&usb_power_supply>;
220 	usb0_vbus-supply = <&reg_usb0_vbus>;
221 	usb1_vbus-supply = <&reg_usb1_vbus>;
222 	usb2_vbus-supply = <&reg_usb2_vbus>;
223 	status = "okay";