Lines Matching +full:charge +full:- +full:status +full:- +full:gpios

5  * This file is dual-licensed: you can use it either under the terms
22  *  b) Permission is hereby granted, free of charge, to any person
44 /dts-v1/;
45 #include "sun7i-a20.dtsi"
46 #include "sunxi-common-regulators.dtsi"
48 #include <dt-bindings/gpio/gpio.h>
49 #include <dt-bindings/input/input.h>
50 #include <dt-bindings/interrupt-controller/irq.h>
54 	compatible = "linksprite,pcduino3", "allwinner,sun7i-a20";
61 		stdout-path = "serial0:115200n8";
65 		compatible = "gpio-leds";
69 			gpios = <&pio 7 15 GPIO_ACTIVE_LOW>;
74 			gpios = <&pio 7 16 GPIO_ACTIVE_LOW>;
78 	gpio-keys {
79 		compatible = "gpio-keys";
84 			gpios = <&pio 7 17 GPIO_ACTIVE_LOW>;
90 			gpios = <&pio 7 18 GPIO_ACTIVE_LOW>;
96 			gpios = <&pio 7 19 GPIO_ACTIVE_LOW>;
102 	target-supply = <&reg_ahci_5v>;
103 	status = "okay";
107 	status = "okay";
111 	cpu-supply = <&reg_dcdc2>;
115 	status = "okay";
119 	status = "okay";
123 	pinctrl-names = "default";
124 	pinctrl-0 = <&gmac_mii_pins>;
125 	phy-handle = <&phy1>;
126 	phy-mode = "mii";
127 	status = "okay";
131 	status = "okay";
135 		interrupt-parent = <&nmi_intc>;
143 	pinctrl-names = "default";
144 	pinctrl-0 = <&ir0_rx_pin>;
145 	status = "okay";
149 	phy1: ethernet-phy@1 {
155 	vmmc-supply = <&reg_vcc3v3>;
156 	bus-width = <4>;
157 	cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
158 	status = "okay";
162 	status = "okay";
166 	status = "okay";
170 	status = "okay";
175 	status = "okay";
179 	regulator-always-on;
180 	regulator-min-microvolt = <1000000>;
181 	regulator-max-microvolt = <1400000>;
182 	regulator-name = "vdd-cpu";
186 	regulator-always-on;
187 	regulator-min-microvolt = <1000000>;
188 	regulator-max-microvolt = <1400000>;
189 	regulator-name = "vdd-int-pll";
193 	regulator-name = "vdd-rtc";
197 	regulator-always-on;
198 	regulator-min-microvolt = <3000000>;
199 	regulator-max-microvolt = <3000000>;
200 	regulator-name = "avcc";
204 	status = "okay";
208 	status = "okay";
212 	pinctrl-names = "default";
213 	pinctrl-0 = <&uart0_pb_pins>;
214 	status = "okay";
219 	status = "okay";
223 	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
224 	usb1_vbus-supply = <&reg_usb1_vbus>;
225 	usb2_vbus-supply = <&reg_usb2_vbus>;
226 	status = "okay";