Lines Matching +full:regulator +full:- +full:soft +full:- +full:start
1 // SPDX-License-Identifier: GPL-2.0
2 #include <dt-bindings/iio/qcom,spmi-vadc.h>
3 #include <dt-bindings/interrupt-controller/irq.h>
4 #include <dt-bindings/spmi/spmi.h>
9 compatible = "qcom,pm8941", "qcom,spmi-pmic";
11 #address-cells = <1>;
12 #size-cells = <0>;
15 compatible = "qcom,pm8941-rtc";
18 reg-names = "rtc", "alarm";
23 compatible = "qcom,pm8941-pwrkey";
27 bias-pull-up;
31 compatible = "qcom,pm8941-misc";
34 interrupt-names = "usb_id";
38 compatible = "qcom,pm8941-charger";
48 interrupt-names = "chg-done",
49 "chg-fast",
50 "chg-trkl",
51 "bat-temp-ok",
52 "bat-present",
53 "chg-gone",
54 "usb-valid",
55 "dc-valid";
57 usb-otg-in-supply = <&pm8941_5vs1>;
59 chg_otg: otg-vbus { };
63 compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio";
65 gpio-controller;
66 gpio-ranges = <&pm8941_gpios 0 0 36>;
67 #gpio-cells = <2>;
68 interrupt-controller;
69 #interrupt-cells = <2>;
71 boost_bypass_n_pin: boost-bypass {
78 compatible = "qcom,pm8941-mpp", "qcom,spmi-mpp";
80 gpio-controller;
81 #gpio-cells = <2>;
92 pm8941_temp: temp-alarm@2400 {
93 compatible = "qcom,spmi-temp-alarm";
96 io-channels = <&pm8941_vadc VADC_DIE_TEMP>;
97 io-channel-names = "thermal";
98 #thermal-sensor-cells = <0>;
102 compatible = "qcom,spmi-vadc";
105 #address-cells = <1>;
106 #size-cells = <0>;
107 #io-channel-cells = <1>;
133 compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc";
136 qcom,external-resistor-micro-ohms = <10000>;
140 compatible = "qcom,pm8941-coincell";
147 compatible = "qcom,pm8941", "qcom,spmi-pmic";
149 #address-cells = <1>;
150 #size-cells = <0>;
153 compatible = "qcom,pm8941-wled";
161 compatible = "qcom,pm8941-regulators";
163 interrupt-names = "ocp-5vs1", "ocp-5vs2";
164 vin_5vs-supply = <&pm8941_5v>;
167 regulator-min-microvolt = <5000000>;
168 regulator-max-microvolt = <5000000>;
169 regulator-enable-ramp-delay = <500>;
173 regulator-enable-ramp-delay = <1000>;
174 regulator-pull-down;
175 regulator-over-current-protection;
176 qcom,ocp-max-retries = <10>;
177 qcom,ocp-retry-delay = <30>;
178 qcom,vs-soft-start-strength = <0>;
179 regulator-initial-mode = <1>;
183 regulator-enable-ramp-delay = <1000>;
184 regulator-pull-down;
185 regulator-over-current-protection;
186 qcom,ocp-max-retries = <10>;
187 qcom,ocp-retry-delay = <30>;
188 qcom,vs-soft-start-strength = <0>;
189 regulator-initial-mode = <1>;