Lines Matching +full:usb +full:- +full:sdp
1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
5 /dts-v1/;
9 #include "omap4-mcpdm.dtsi"
12 model = "TI OMAP4 SDP board";
13 compatible = "ti,omap4-sdp", "ti,omap4430", "ti,omap4";
26 vdd_eth: fixedregulator-vdd-eth {
27 pinctrl-names = "default";
28 pinctrl-0 = <&enet_enable_gpio>;
30 compatible = "regulator-fixed";
31 regulator-name = "VDD_ETH";
32 regulator-min-microvolt = <3300000>;
33 regulator-max-microvolt = <3300000>;
35 enable-active-high;
36 regulator-boot-on;
37 startup-delay-us = <25000>;
40 vbat: fixedregulator-vbat {
41 compatible = "regulator-fixed";
42 regulator-name = "VBAT";
43 regulator-min-microvolt = <3750000>;
44 regulator-max-microvolt = <3750000>;
45 regulator-boot-on;
49 compatible = "gpio-leds";
92 compatible = "pwm-leds";
96 max-brightness = <127>;
102 max-brightness = <255>;
107 compatible = "pwm-backlight";
109 brightness-levels = <
114 default-brightness-level = <13>;
118 compatible = "ti,abe-twl6040";
121 ti,jack-detection = <1>;
122 ti,mclk-freq = <38400000>;
130 ti,audio-routing =
154 pinctrl-names = "default";
155 pinctrl-0 = <&wl12xx_gpio>;
156 compatible = "regulator-fixed";
157 regulator-name = "vwl1271";
158 regulator-min-microvolt = <1800000>;
159 regulator-max-microvolt = <1800000>;
161 startup-delay-us = <70000>;
162 enable-active-high;
173 #address-cells = <1>;
174 #size-cells = <0>;
180 remote-endpoint = <&hdmi_out>;
188 remote-endpoint = <&hdmi_connector_in>;
195 compatible = "hdmi-connector";
202 remote-endpoint = <&tpd12s015_out>;
209 pinctrl-names = "default";
210 pinctrl-0 = <
216 pinctrl-single,pins = <
225 pinctrl-single,pins = <
234 pinctrl-single,pins = <
241 pinctrl-single,pins = <
248 pinctrl-single,pins = <
257 pinctrl-single,pins = <
266 pinctrl-single,pins = <
275 pinctrl-single,pins = <
284 pinctrl-single,pins = <
292 pinctrl-single,pins = <
300 pinctrl-single,pins = <
307 pinctrl-single,pins = <
314 pinctrl-single,pins = <
321 pinctrl-single,pins = <
329 pinctrl-single,pins = <
336 pinctrl-single,pins = <
349 pinctrl-single,pins = <
355 pinctrl-single,pins = <
363 * We could use gpio-hog to keep it high, but let's use
372 pinctrl-names = "default";
373 pinctrl-0 = <&i2c1_pins>;
375 clock-frequency = <400000>;
379 /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */
385 #clock-cells = <0>;
388 pinctrl-names = "default";
389 pinctrl-0 = <&twl6040_pins>;
391 /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */
393 ti,audpwron-gpio = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio line 127 */
395 vio-supply = <&v1v8>;
396 v2v1-supply = <&v2v1>;
397 enable-active-high;
400 vddvibl-supply = <&vbat>;
401 vddvibr-supply = <&vbat>;
405 ti,vibldrv-res = <8>;
406 ti,vibrdrv-res = <3>;
407 ti,viblmotor-res = <10>;
408 ti,vibrmotor-res = <10>;
417 pinctrl-names = "default";
418 pinctrl-0 = <&i2c2_pins>;
420 clock-frequency = <400000>;
424 pinctrl-names = "default";
425 pinctrl-0 = <&i2c3_pins>;
427 clock-frequency = <400000>;
440 * http://www.rohm.com/products/databook/sensor/pdf/bh1780gli-e.pdf
449 pinctrl-names = "default";
450 pinctrl-0 = <&i2c4_pins>;
452 clock-frequency = <400000>;
455 * 3-Axis Digital Compass
465 pinctrl-names = "default";
466 pinctrl-0 = <&mcspi1_pins>;
469 pinctrl-names = "default";
470 pinctrl-0 = <&ks8851_pins>;
473 spi-max-frequency = <24000000>;
475 interrupt-parent = <&gpio2>;
477 vdd-supply = <&vdd_eth>;
478 reset-gpios = <&gpio5 10 GPIO_ACTIVE_HIGH>;
483 vmmc-supply = <&vmmc>;
484 bus-width = <8>;
488 vmmc-supply = <&vaux1>;
489 bus-width = <8>;
490 ti,non-removable;
502 pinctrl-names = "default";
503 pinctrl-0 = <&wl12xx_pins>;
504 vmmc-supply = <&wl12xx_vmmc>;
505 non-removable;
506 bus-width = <4>;
507 cap-power-off-card;
509 #address-cells = <1>;
510 #size-cells = <0>;
514 interrupt-parent = <&gpio1>;
516 ref-clock-frequency = <26000000>;
517 tcxo-clock-frequency = <26000000>;
522 cs1-used;
523 device-handle = <&elpida_ECB240ABACN>;
527 cs1-used;
528 device-handle = <&elpida_ECB240ABACN>;
532 keypad,num-rows = <8>;
533 keypad,num-columns = <8>;
598 linux,input-no-autorepeat;
602 interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
604 pinctrl-names = "default";
605 pinctrl-0 = <&uart2_pins>;
609 interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
611 pinctrl-names = "default";
612 pinctrl-0 = <&uart3_pins>;
616 interrupts-extended = <&wakeupgen GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH
618 pinctrl-names = "default";
619 pinctrl-0 = <&uart4_pins>;
623 pinctrl-names = "default";
624 pinctrl-0 = <&mcbsp1_pins>;
629 pinctrl-names = "default";
630 pinctrl-0 = <&mcbsp2_pins>;
635 pinctrl-names = "default";
636 pinctrl-0 = <&dmic_pins>;
641 usb-supply = <&vusb>;
645 interface-type = <1>;
656 vdd-supply = <&vcxio>;
660 remote-endpoint = <&lcd0_in>;
666 compatible = "tpo,taal", "panel-dsi-cm";
670 reset-gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */
674 remote-endpoint = <&dsi1_out_ep>;
682 vdd-supply = <&vcxio>;
686 remote-endpoint = <&lcd1_in>;
692 compatible = "tpo,taal", "panel-dsi-cm";
696 reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */
700 remote-endpoint = <&dsi2_out_ep>;
708 vdda-supply = <&vdac>;
712 remote-endpoint = <&tpd12s015_in>;