Lines Matching +full:bus +full:- +full:range +full:- +full:microvolt
1 // SPDX-License-Identifier: GPL-2.0 OR MIT
7 /dts-v1/;
9 #include <dt-bindings/gpio/gpio.h>
12 model = "Hardkernel ODROID-C1";
13 compatible = "hardkernel,odroid-c1", "amlogic,meson8b";
22 stdout-path = "serial0:115200n8";
30 emmc_pwrseq: emmc-pwrseq {
31 compatible = "mmc-pwrseq-emmc";
32 reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
36 compatible = "gpio-leds";
40 linux,default-trigger = "heartbeat";
41 default-state = "off";
45 p5v0: regulator-p5v0 {
46 compatible = "regulator-fixed";
48 regulator-name = "P5V0";
49 regulator-min-microvolt = <5000000>;
50 regulator-max-microvolt = <5000000>;
53 tflash_vdd: regulator-tflash_vdd {
57 compatible = "regulator-fixed";
59 regulator-name = "TFLASH_VDD";
60 regulator-min-microvolt = <3300000>;
61 regulator-max-microvolt = <3300000>;
63 vin-supply = <&vcc_3v3>;
66 enable-active-high;
69 tf_io: gpio-regulator-tf_io {
70 compatible = "regulator-gpio";
72 regulator-name = "TF_IO";
73 regulator-min-microvolt = <1800000>;
74 regulator-max-microvolt = <3300000>;
76 vin-supply = <&vcc_3v3>;
82 gpios-states = <0>;
88 iio-hwmon {
89 compatible = "iio-hwmon";
90 io-channels = <&saradc 8>;
93 rtc32k_xtal: rtc32k-xtal-clk {
95 compatible = "fixed-clock";
96 clock-frequency = <32768>;
97 clock-output-names = "RTC32K";
98 #clock-cells = <0>;
101 vcc_1v8: regulator-vcc-1v8 {
107 compatible = "regulator-fixed";
109 regulator-name = "VCC1V8";
110 regulator-min-microvolt = <1800000>;
111 regulator-max-microvolt = <1800000>;
113 vin-supply = <&p5v0>;
116 vcc_3v3: regulator-vcc-3v3 {
122 compatible = "regulator-fixed";
124 regulator-name = "VCC3V3";
125 regulator-min-microvolt = <3300000>;
126 regulator-max-microvolt = <3300000>;
128 vin-supply = <&p5v0>;
131 vcck: regulator-vcck {
133 compatible = "pwm-regulator";
135 regulator-name = "VCCK";
136 regulator-min-microvolt = <860000>;
137 regulator-max-microvolt = <1140000>;
139 vin-supply = <&p5v0>;
142 pwm-dutycycle-range = <91 0>;
144 regulator-boot-on;
145 regulator-always-on;
148 vddc_ddr: regulator-vddc-ddr {
154 compatible = "regulator-fixed";
156 regulator-name = "DDR_VDDC";
157 regulator-min-microvolt = <1500000>;
158 regulator-max-microvolt = <1500000>;
160 vin-supply = <&p5v0>;
163 vddee: regulator-vddee {
165 compatible = "pwm-regulator";
167 regulator-name = "VDDEE";
168 regulator-min-microvolt = <860000>;
169 regulator-max-microvolt = <1140000>;
171 vin-supply = <&p5v0>;
174 pwm-dutycycle-range = <91 0>;
176 regulator-boot-on;
177 regulator-always-on;
180 vdd_rtc: regulator-vdd-rtc {
185 compatible = "regulator-fixed";
187 regulator-name = "VDD_RTC";
188 regulator-min-microvolt = <900000>;
189 regulator-max-microvolt = <900000>;
191 vin-supply = <&vcc_3v3>;
196 cpu-supply = <&vcck>;
208 pinctrl-0 = <ð_rgmii_pins>;
209 pinctrl-names = "default";
211 phy-handle = <ð_phy>;
212 phy-mode = "rgmii-id";
214 nvmem-cells = <ðernet_mac_address>;
215 nvmem-cell-names = "mac-address";
218 compatible = "snps,dwmac-mdio";
219 #address-cells = <1>;
220 #size-cells = <0>;
223 eth_phy: ethernet-phy@0 {
226 reset-assert-us = <10000>;
227 reset-deassert-us = <30000>;
228 reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
230 interrupt-parent = <&gpio_intc>;
238 gpio-line-names = /* Bank GPIOX */
282 gpio-line-names = "UART TX", "UART RX", "",
291 * WARNING: The USB Hub on the Odroid-C1/C1+ needs a reset signal
294 * in order to reset the Hub when USB bus is powered down.
296 usb-hub {
297 gpio-hog;
299 output-high;
300 line-name = "usb-hub-reset";
306 pinctrl-0 = <&ir_recv_pins>;
307 pinctrl-names = "default";
311 mali-supply = <&vddee>;
316 vref-supply = <&vcc_1v8>;
322 pinctrl-0 = <&sdxc_c_pins>;
323 pinctrl-names = "default";
325 bus-width = <8>;
326 max-frequency = <100000000>;
328 disable-wp;
329 cap-mmc-highspeed;
330 mmc-hs200-1_8v;
331 no-sdio;
333 mmc-pwrseq = <&emmc_pwrseq>;
335 vmmc-supply = <&vcc_3v3>;
336 vqmmc-supply = <&vcc_1v8>;
342 pinctrl-0 = <&sd_b_pins>;
343 pinctrl-names = "default";
347 compatible = "mmc-slot";
351 bus-width = <4>;
352 no-sdio;
353 cap-mmc-highspeed;
354 cap-sd-highspeed;
355 disable-wp;
357 cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
359 vmmc-supply = <&tflash_vdd>;
360 vqmmc-supply = <&tf_io>;
366 pinctrl-0 = <&pwm_c1_pins>, <&pwm_d_pins>;
367 pinctrl-names = "default";
369 clock-names = "clkin0", "clkin1";
375 vdd-supply = <&vdd_rtc>;
380 pinctrl-0 = <&uart_ao_a_pins>;
381 pinctrl-names = "default";