Lines Matching +full:poll +full:- +full:retry +full:- +full:count
4 * This file is dual-licensed: you can use it either under the terms
44 /dts-v1/;
46 #include <dt-bindings/gpio/gpio.h>
47 #include <dt-bindings/interrupt-controller/irq.h>
51 compatible = "uniwest,imx6q-evi", "fsl,imx6q";
58 reg_usbh1_vbus: regulator-usbhubreset {
59 compatible = "regulator-fixed";
60 regulator-name = "usbh1_vbus";
61 regulator-min-microvolt = <5000000>;
62 regulator-max-microvolt = <5000000>;
63 enable-active-high;
64 startup-delay-us = <2>;
65 pinctrl-names = "default";
66 pinctrl-0 = <&pinctrl_usbh1_hubreset>;
70 reg_usb_otg_vbus: regulator-usbotgvbus {
71 compatible = "regulator-fixed";
72 regulator-name = "usb_otg_vbus";
73 regulator-min-microvolt = <5000000>;
74 regulator-max-microvolt = <5000000>;
75 pinctrl-names = "default";
76 pinctrl-0 = <&pinctrl_usbotgvbus>;
78 enable-active-high;
79 regulator-always-on;
87 remote-endpoint = <&lvds0_out>;
94 cs-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
95 pinctrl-names = "default";
96 pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1cs>;
100 compatible = "altr,fpga-passive-serial";
101 spi-max-frequency = <20000000>;
103 pinctrl-0 = <&pinctrl_fpgaspi>;
104 nconfig-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
105 nstat-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
110 cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
113 pinctrl-names = "default";
114 pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3cs>;
119 cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>,
123 pinctrl-names = "default";
124 pinctrl-0 = <&pinctrl_ecspi5 &pinctrl_ecspi5cs>;
131 address-width = <24>;
132 spi-max-frequency = <5000000>;
137 compatible = "nxp,rtc-pcf2123";
138 spi-max-frequency = <2450000>;
139 spi-cs-high;
145 pinctrl-names = "default";
146 pinctrl-0 = <&pinctrl_enet>;
147 phy-mode = "rgmii";
148 phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
149 interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
151 fsl,err006687-workaround-present;
156 pinctrl-names = "default";
157 pinctrl-0 = <&pinctrl_gpminand>;
162 pinctrl-names = "default";
163 pinctrl-0 = <&pinctrl_i2c2>;
164 clock-frequency = <100000>;
169 pinctrl-names = "default", "gpio";
170 pinctrl-0 = <&pinctrl_i2c3>;
171 pinctrl-1 = <&pinctrl_i2c3_gpio>;
172 clock-frequency = <100000>;
173 scl-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
174 sda-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
177 battery: sbs-battery@b {
178 compatible = "sbs,sbs-battery";
180 sbs,poll-retry-count = <100>;
181 sbs,i2c-retry-count = <100>;
188 lvds0: lvds-channel@0 {
194 remote-endpoint = <&panel_in>;
205 pinctrl-names = "default";
206 pinctrl-0 = <&pinctrl_uart1>;
211 pinctrl-names = "default";
212 pinctrl-0 = <&pinctrl_uart2>;
217 vbus-supply = <®_usbh1_vbus>;
218 pinctrl-names = "default";
219 pinctrl-0 = <&pinctrl_usbh1>;
221 disable-over-current;
226 vbus-supply = <®_usb_otg_vbus>;
227 pinctrl-names = "default";
228 pinctrl-0 = <&pinctrl_usbotg>;
229 disable-over-current;
235 pinctrl-names = "default";
236 pinctrl-0 = <&pinctrl_usdhc1>;
237 non-removable;
243 pinctrl-names = "default";
244 pinctrl-0 = <&pinctrl_weimfpga &pinctrl_weimcs>;
249 pinctrl-names = "default";
250 pinctrl-0 = <&pinctrl_hog>;