Lines Matching +full:super +full:- +full:speed
15 Addresses scanned: ISA address retrieved from Super I/O registers
19 * Nuvoton NCT5572D/NCT6771F/NCT6772F/NCT6775F/W83677HG-I
23 Addresses scanned: ISA address retrieved from Super I/O registers
31 Addresses scanned: ISA address retrieved from Super I/O registers
39 Addresses scanned: ISA address retrieved from Super I/O registers
47 Addresses scanned: ISA address retrieved from Super I/O registers
55 Addresses scanned: ISA address retrieved from Super I/O registers
63 Addresses scanned: ISA address retrieved from Super I/O registers
71 Addresses scanned: ISA address retrieved from Super I/O registers
79 Addresses scanned: ISA address retrieved from Super I/O registers
87 Guenter Roeck <linux@roeck-us.net>
90 -----------
93 and compatible super I/O chips.
100 There are 4 to 5 fan rotation speed sensors, 8 to 15 analog voltage sensors,
114 triggered if the rotation speed has dropped below a programmable limit. On
117 do not have a fan speed divider. The driver sets the most suitable fan divisor
118 itself; specifically, it increases the divider value each time a fan speed
119 reading returns an invalid value, and it reduces it if the fan speed reading
132 The mode works for fan1-fan5.
135 ----------------
137 pwm[1-7]
138 - this file stores PWM duty cycle or DC value (fan speed) in range:
140 0 (lowest speed) to 255 (full)
142 pwm[1-7]_enable
143 - this file controls mode of fan/temperature control:
145 * 0 Fan control disabled (fans set to maximum speed)
146 * 1 Manual mode, write to pwm[0-5] any value 0-255
148 * 3 "Fan Speed Cruise" mode
152 pwm[1-7]_mode
153 - controls if output is PWM or DC level
159 -----------------------------
161 pwm[1-7]_temp_sel
165 pwm[1-7]_weight_temp_sel
173 pwm[1-7]_weight_duty_step
176 pwm[1-7]_weight_temp_step
181 pwm[1-7]_weight_temp_step_base
185 pwm[1-7]_weight_temp_step_tol
189 -----------------------
193 pwm[1-7]_target_temp
195 (range 0 - 127000)
197 pwm[1-7]_temp_tolerance
200 There are no changes to fan speed. Once the temperature leaves the interval, fan
201 speed increases (if temperature is higher that desired) or decreases (if
205 pwm[1-7]_start
206 fan pwm start value (range 1 - 255), to start fan
209 pwm[1-7]_floor
210 lowest fan pwm (range 0 - 255) if temperature is below
214 pwm[1-7]_step_up_time
215 milliseconds before fan speed is increased
217 pwm[1-7]_step_down_time
218 milliseconds before fan speed is decreased
220 pwm[1-7]_stop_time
225 Speed Cruise mode (3)
226 ---------------------
228 This modes tries to keep the fan speed constant.
230 fan[1-7]_target
231 Target fan speed
233 fan[1-7]_tolerance
234 Target speed tolerance
240 ---------------------
242 This mode offers multiple slopes to control the fan speed. The slopes can be
248 critical temperature mode, in which the fans should run at full speed.
250 pwm[1-7]_auto_point[1-7]_pwm
254 pwm[1-7]_auto_point[1-7]_temp
257 pwm[1-7]_temp_tolerance
260 pwm[1-7]_crit_temp_tolerance
264 pwm[1-7]_step_up_time
265 milliseconds before fan speed is increased
267 pwm[1-7]_step_down_time
268 milliseconds before fan speed is decreased
271 -----------
274 connected to anything and floats, or that it is connected to some non-standard
278 temperature increases (similar to the raw PECI temperature value - see PECI