Lines Matching +full:1 +full:v
64 temp[1-3] (2 remote diodes and 1 internal), 8 voltages in[0-7] (7 external and
65 1 internal) and up to 6 fan speeds fan[1-6]. Additionally, the chips implement
66 up to 5 PWM outputs pwm[1-3,5-6] for controlling fan speeds both manually and
69 For the DME1737, A8000 and SCH5027, fan[1-2] and pwm[1-2] are always present.
74 For the SCH311x and SCH5127, fan[1-3] and pwm[1-3] are always present and
94 in0: +5VTR (+5V standby) 0V - 6.64V
95 in1: Vccp (processor core) 0V - 3V
96 in2: VCC (internal +3.3V) 0V - 4.38V
97 in3: +5V 0V - 6.64V
98 in4: +12V 0V - 16V
99 in5: VTR (+3.3V standby) 0V - 4.38V
100 in6: Vbat (+3.0V) 0V - 4.38V
104 in0: +2.5V 0V - 3.32V
105 in1: Vccp (processor core) 0V - 2V
106 in2: VCC (internal +3.3V) 0V - 4.38V
107 in3: +5V 0V - 6.64V
108 in4: +12V 0V - 16V
109 in5: VTR (+3.3V standby) 0V - 4.38V
110 in6: Vbat (+3.0V) 0V - 4.38V
114 in0: +5VTR (+5V standby) 0V - 6.64V
115 in1: Vccp (processor core) 0V - 3V
116 in2: VCC (internal +3.3V) 0V - 4.38V
117 in3: V2_IN 0V - 1.5V
118 in4: V1_IN 0V - 1.5V
119 in5: VTR (+3.3V standby) 0V - 4.38V
120 in6: Vbat (+3.0V) 0V - 4.38V
124 in0: +2.5 0V - 3.32V
125 in1: Vccp (processor core) 0V - 3V
126 in2: VCC (internal +3.3V) 0V - 4.38V
127 in3: V2_IN 0V - 1.5V
128 in4: V1_IN 0V - 1.5V
129 in5: VTR (+3.3V standby) 0V - 4.38V
130 in6: Vbat (+3.0V) 0V - 4.38V
131 in7: Vtrip (+1.5V) 0V - 1.99V
147 temp1: Remote diode 1 (3904 type) temperature -127C - +127C
153 returns 1 when a faulty diode or an unconnected input is detected and 0
162 alarm when crossed. Fan inputs 1-4 provide type attributes that need to be set
164 generates. Supported values are 1, 2, and 4. Fan inputs 5-6 only support fans
173 This chip features 5 PWM outputs. PWM outputs 1-3 are associated with fan
174 inputs 1-3 and PWM outputs 5-6 are associated with fan inputs 5-6. PWM outputs
175 1-3 can be configured to operate either in manual or automatic mode by setting
188 be retrieved via the zone[1-3]_auto_channels_temp attributes. Each PWM output
190 pwm[1-3]_auto_channels_zone attributes. Each PWM output has 3 distinct output
192 and low and min can be programmed via pwm[1-3]_auto_point1_pwm and
193 pwm[1-3]_auto_pwm_min, respectively. The thermal thresholds of the zones are
194 programmed via zone[1-3]_auto_point[1-3]_temp and
195 zone[1-3]_auto_point1_temp_hyst:
198 pwm[1-3]_auto_point2_pwm full-speed duty-cycle (255, i.e., 100%)
199 pwm[1-3]_auto_point1_pwm low-speed duty-cycle
200 pwm[1-3]_auto_pwm_min min-speed duty-cycle
202 zone[1-3]_auto_point3_temp full-speed temp (all outputs)
203 zone[1-3]_auto_point2_temp full-speed temp
204 zone[1-3]_auto_point1_temp low-speed temp
205 zone[1-3]_auto_point1_temp_hyst min-speed temp
254 in[0-7]_alarm RO Voltage input alarm. Returns 1 if
258 temp[1-3]_input RO Measured temperature in millidegree
260 temp[1-3]_min RW Low limit for temp input.
261 temp[1-3]_max RW High limit for temp input.
262 temp[1-3]_offset RW Offset for temp input. This value will
265 temp[1-3]_alarm RO Alarm for temp input. Returns 1 if temp
268 temp[1-3]_fault RO Temp input fault. Returns 1 if the chip
272 zone[1-3]_auto_channels_temp RO Temperature zone to temperature input
276 - 1: temp1
279 zone[1-3]_auto_point1_temp_hyst RW Auto PWM temp point1 hysteresis. The
284 zone[1-3]_auto_point[1-3]_temp RW Auto PWM temp points. Auto_point1 is
290 fan[1-6]_input RO Measured fan speed in RPM.
291 fan[1-6]_min RW Low limit for fan input.
292 fan[1-6]_alarm RO Alarm for fan input. Returns 1 if fan
295 fan[1-4]_type RW Type of attached fan. Expressed in
298 1, 2, and 4.
303 pmw[1-3,5-6] RO/RW Duty-cycle of PWM output. Supported
307 pwm[1-3]_enable RW Enable of PWM outputs 1-3. Supported
311 - 1: manual mode
314 returns 1 since these 2 outputs are
316 pmw[1-3,5-6]_freq RW Frequency of PWM output. Supported
319 pmw[1-3]_ramp_rate RW Ramp rate of PWM output. Determines how
326 pwm[1-3]_auto_channels_zone RW PWM output to temperature zone mapping.
330 - 1: zone1
334 - 7: highest of zone[1-3]
335 pwm[1-3]_auto_pwm_min RW Auto PWM min pwm. Minimum PWM duty-
338 pwm[1-3]_auto_point1_pwm RW Auto PWM pwm point. Auto_point1 is the
340 pwm[1-3]_auto_point2_pwm RO Auto PWM pwm point. Auto_point2 is the
351 temp[1-3]_offset yes yes
354 zone[1-3]_hyst yes yes