Lines Matching +full:tx +full:- +full:enable
3 DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties
7 - compatible: must be "snps,dwc3"
8 - reg : Address and length of the register set for the device
9 - interrupts: Interrupts used by the dwc3 controller.
10 - clock-names: list of clock names. Ideally should be "ref",
12 - clocks: list of phandle and clock specifier pairs corresponding to
13 entries in the clock-names property.
16 clocks are optional if the parent node (i.e. glue-layer) is compatible to
18 "cavium,octeon-7130-usb-uctl"
20 "samsung,exynos5250-dwusb3"
21 "samsung,exynos5433-dwusb3"
22 "samsung,exynos7-dwusb3"
23 "sprd,sc9860-dwc3"
24 "st,stih407-dwc3"
25 "ti,am437x-dwc3"
27 "ti,keystone-dwc3"
28 "rockchip,rk3399-dwc3"
29 "xlnx,zynqmp-dwc3"
32 - usb-phy : array of phandle for the PHY device. The first element
35 - phys: from the *Generic PHY* bindings
36 - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy"
37 or "usb3-phy".
38 - resets: set of phandle and reset specifier pairs
39 - snps,usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM
40 - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable
41 - snps,dis-start-transfer-quirk: when set, disable isoc START TRANSFER command
42 failure SW work-around for DWC_usb31 version 1.70a-ea06
44 - snps,disable_scramble_quirk: true when SW should disable data scrambling.
46 - snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled
47 - snps,lpm-nyet-threshold: LPM NYET threshold
48 - snps,u2exit_lfps_quirk: set if we want to enable u2exit lfps quirk
49 - snps,u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk
50 - snps,req_p1p2p3_quirk: when set, the core will always request for
52 - snps,del_p1p2p3_quirk: when set core will delay P1/P2/P3 until a certain
54 - snps,del_phy_power_chg_quirk: when set core will delay PHY power change
56 - snps,lfps_filter_quirk: when set core will filter LFPS reception.
57 - snps,rx_detect_poll_quirk: when set core will disable a 400us delay to start
59 - snps,tx_de_emphasis_quirk: when set core will set Tx de-emphasis value.
60 - snps,tx_de_emphasis: the value driven to the PHY is controlled by the
62 - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy.
63 - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy.
64 - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG,
66 - snps,dis-u1-entry-quirk: set if link entering into U1 needs to be disabled.
67 - snps,dis-u2-entry-quirk: set if link entering into U2 needs to be disabled.
68 - snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection
70 - snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists
72 a free-running PHY clock.
73 - snps,dis-del-phy-power-chg-quirk: when set core will change PHY power
75 - snps,dis-tx-ipgap-linecheck-quirk: when set, disable u2mac linestate check
77 - snps,parkmode-disable-ss-quirk: when set, all SuperSpeed bus instances in
79 - snps,dis_metastability_quirk: when set, disable metastability workaround.
81 - snps,dis-split-quirk: when set, change the way URBs are handled by the
82 driver. Needed to avoid -EPROTO errors with usbhid
84 - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal
86 - snps,hird-threshold: HIRD threshold
87 - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for
89 - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ
90 register for post-silicon frame length adjustment when the
92 - snps,rx-thr-num-pkt-prd: periodic ESS RX packet threshold count - host mode
93 only. Set this and rx-max-burst-prd to a valid,
94 non-zero value 1-16 (DWC_usb31 programming guide
95 section 1.2.4) to enable periodic ESS RX threshold.
96 - snps,rx-max-burst-prd: max periodic ESS RX burst size - host mode only. Set
97 this and rx-thr-num-pkt-prd to a valid, non-zero value
98 1-16 (DWC_usb31 programming guide section 1.2.4) to
99 enable periodic ESS RX threshold.
100 - snps,tx-thr-num-pkt-prd: periodic ESS TX packet threshold count - host mode
101 only. Set this and tx-max-burst-prd to a valid,
102 non-zero value 1-16 (DWC_usb31 programming guide
103 section 1.2.3) to enable periodic ESS TX threshold.
104 - snps,tx-max-burst-prd: max periodic ESS TX burst size - host mode only. Set
105 this and tx-thr-num-pkt-prd to a valid, non-zero value
106 1-16 (DWC_usb31 programming guide section 1.2.3) to
107 enable periodic ESS TX threshold.
109 - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated.
110 - snps,incr-burst-type-adjustment: Value for INCR burst type of GSBUSCFG0
111 register, undefined length INCR burst type enable and INCRx type.
116 - in addition all properties from usb-xhci.txt from the current directory are
126 usb-phy = <&usb2_phy>, <&usb3,phy>;
127 snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;