Lines Matching +full:8 +full:- +full:channel
7 - compatible: "st,sta350"
8 - reg: the I2C address of the device for I2C
9 - reset-gpios: a GPIO spec for the reset pin. If specified, it will be
12 - power-down-gpios: a GPIO spec for the power down pin. If specified,
16 - vdd-dig-supply: regulator spec, providing 3.3V
17 - vdd-pll-supply: regulator spec, providing 3.3V
18 - vcc-supply: regulator spec, providing 5V - 26V
22 - st,output-conf: number, Selects the output configuration:
23 0: 2-channel (full-bridge) power, 2-channel data-out
24 1: 2 (half-bridge). 1 (full-bridge) on-board power
25 2: 2 Channel (Full-Bridge) Power, 1 Channel FFX
26 3: 1 Channel Mono-Parallel
28 This property has to be specified as '/bits/ 8' value.
30 - st,ch1-output-mapping: Channel 1 output mapping
31 - st,ch2-output-mapping: Channel 2 output mapping
32 - st,ch3-output-mapping: Channel 3 output mapping
33 0: Channel 1
34 1: Channel 2
35 2: Channel 3
36 If parameter is missing, channel 1 is chosen.
37 This properties have to be specified as '/bits/ 8' values.
39 - st,thermal-warning-recover:
42 - st,thermal-warning-adjustment:
45 - st,fault-detect-recovery:
48 - st,ffx-power-output-mode: string
51 - "drop-compensation"
52 - "tapered-compensation"
53 - "full-power-mode"
54 - "variable-drop-compensation" (default)
56 - st,drop-compensation-ns: number
57 Only required for "st,ffx-power-output-mode" ==
58 "variable-drop-compensation".
63 - st,overcurrent-warning-adjustment:
66 - st,max-power-use-mpcc:
70 - st,max-power-corr:
74 - st,am-reduction-mode:
78 - st,odd-pwm-speed-mode:
82 - st,distortion-compensation:
86 - st,invalid-input-detect-mute:
89 - st,activate-mute-output:
91 reach a value lower than -76 dBFS.
93 - st,bridge-immediate-off:
95 power-down-gpio goes low. Otherwise, the bridge will wait for 13
98 - st,noise-shape-dc-cut:
99 If present, the noise-shaping technique on the DC cutoff filter are
102 - st,powerdown-master-volume:
103 If present, the power-down pin and I2C power-down functions will
107 - st,powerdown-delay-divider:
108 If present, the bridge power-down time will be divided by the provided
110 are 1, 2, 4, 8, 16, 32, 64 and 128.
111 This property has to be specified as '/bits/ 8' value.
118 reset-gpios = <&gpio1 19 0>;
119 power-down-gpios = <&gpio1 16 0>;
120 st,output-conf = /bits/ 8 <0x3>; // set output to 2-channel
121 // (full-bridge) power,
122 // 2-channel data-out
123 st,ch1-output-mapping = /bits/ 8 <0>; // set channel 1 output ch 1
124 st,ch2-output-mapping = /bits/ 8 <0>; // set channel 2 output ch 1
125 st,ch3-output-mapping = /bits/ 8 <0>; // set channel 3 output ch 1
126 st,max-power-correction; // enables power bridge
129 st,invalid-input-detect-mute; // mute if no valid digital