Lines Matching full:pinctrl
1 One-register-per-pin type device tree based pinctrl driver
4 - compatible : "pinctrl-single" or "pinconf-single".
5 "pinctrl-single" means that pinconf isn't supported.
10 - #pinctrl-cells : number of cells in addition to the index, set to 1
11 for pinctrl-single,pins and 2 for pinctrl-single,bits
13 - pinctrl-single,register-width : pinmux register access width in bits
15 - pinctrl-single,function-mask : mask of allowed pinmux function bits
19 - pinctrl-single,function-off : function off mode for disabled state if
23 - pinctrl-single,bit-per-mux : boolean to indicate that one register controls
24 more than one pin, for which "pinctrl-single,function-mask" property specifies
27 - pinctrl-single,drive-strength : array of value that are used to configure
32 pinctrl-single,power-source = <0x30 0xf0>;
34 - pinctrl-single,bias-pullup : array of value that are used to configure the
38 pinctrl-single,bias-pullup = <0 1 0 1>;
40 - pinctrl-single,bias-pulldown : array of value that are used to configure the
44 pinctrl-single,bias-pulldown = <2 2 0 2>;
47 pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. One bit means
50 use pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. Input bias
53 pinctrl-single,bias-disable. Because pinctrl single driver could implement
56 - pinctrl-single,input-schmitt : array of value that are used to configure
61 pinctrl-single,input-schmitt = <0x30 0x70>;
63 - pinctrl-single,input-schmitt-enable : array of value that are used to
67 pinctrl-single,input-schmitt-enable = <0x30 0x40 0 0x70>;
69 - pinctrl-single,low-power-mode : array of value that are used to configure
74 pinctrl-single,low-power-mode = <0x288 0x388>;
76 - pinctrl-single,gpio-range : list of value that are used to configure a GPIO
77 range. They're value of subnode phandle, pin base in pinctrl device, pin
79 The number of parameters is depend on #pinctrl-single,gpio-range-cells
83 pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1>;
86 interrupts for wake-up events for example. In this case pinctrl-single
93 pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as
94 specified in the pinctrl-bindings.txt document in this directory.
96 The pin configuration nodes for pinctrl-single are specified as pinctrl
97 register offset and values using pinctrl-single,pins. Only the bits specified
98 in pinctrl-single,function-mask are updated.
100 When #pinctrl-cells = 1, then setting a pin for a device could be done with:
102 pinctrl-single,pins = <0xdc 0x118>;
104 Where 0xdc is the offset from the pinctrl register base address for the device
105 pinctrl register, and 0x118 contains the desired value of the pinctrl register.
107 When #pinctrl-cells = 2, then setting a pin for a device could be done with:
109 pinctrl-single,pins = <0xdc 0x30 0x07>;
116 pinctrl-single,bits need to be used which takes three parameters:
118 pinctrl-single,bits = <0xdc 0x18 0xff>;
120 Where 0xdc is the offset from the pinctrl register base address for the
121 device pinctrl register, 0x18 is the desired value, and 0xff is the sub mask to
127 by pinctrl-single,gpio-range property.
130 - #pinctrl-single,gpio-range-cells : the number of parameters after phandle in
131 pinctrl-single,gpio-range property.
134 #pinctrl-single,gpio-range-cells = <3>;
144 compatible = "pinctrl-single";
150 pinctrl-single,register-width = <16>;
151 pinctrl-single,function-mask = <0xffff>;
156 compatible = "pinctrl-single";
162 pinctrl-single,register-width = <16>;
163 pinctrl-single,function-mask = <0xffff>;
167 compatible = "pinctrl-single";
171 pinctrl-single,bit-per-mux;
172 pinctrl-single,register-width = <32>;
173 pinctrl-single,function-mask = <0x5F>;
184 pinctrl-single,register-width = <32>;
185 pinctrl-single,function-mask = <7>;
188 pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1
194 #pinctrl-single,gpio-range-cells = <3>;
204 * map all board specific static pins enabled by the pinctrl driver
207 pinctrl-names = "default";
208 pinctrl-0 = <&board_pins>;
211 pinctrl-single,pins = <
220 pinctrl-single,pins = <
224 pinctrl-single,bias-pulldown = <0 2 2>;
225 pinctrl-single,bias-pullup = <0 1 1>;
230 pinctrl-single,pins = <
241 pinctrl-single,bits = <
247 pinctrl-single,bits = <
255 pinctrl-names = "default";
256 pinctrl-0 = <&uart0_pins>;
260 pinctrl-names = "default";
261 pinctrl-0 = <&uart2_pins>;