Lines Matching +full:rx +full:- +full:delay +full:- +full:ps
4 to clock delays. You can specify clock delay values in the PHY OF
8 Note that these settings are applied after any phy-specific fixup from
15 value is 0, the maximum value is 3000, and it can be specified in 200ps
17 skew values actually increase in 120ps steps, starting from -840ps. The
23 The following table shows the actual skew delay you will get for each of the
27 Device Tree Value Delay Pad Skew Register Value
28 -----------------------------------------------------
29 0 -840ps 0000
30 200 -720ps 0001
31 400 -600ps 0010
32 600 -480ps 0011
33 800 -360ps 0100
34 1000 -240ps 0101
35 1200 -120ps 0110
36 1400 0ps 0111
37 1600 120ps 1000
38 1800 240ps 1001
39 2000 360ps 1010
40 2200 480ps 1011
41 2400 600ps 1100
42 2600 720ps 1101
43 2800 840ps 1110
44 3000 960ps 1111
48 - rxc-skew-ps : Skew control of RXC pad
49 - rxdv-skew-ps : Skew control of RX CTL pad
50 - txc-skew-ps : Skew control of TXC pad
51 - txen-skew-ps : Skew control of TX CTL pad
52 - rxd0-skew-ps : Skew control of RX data 0 pad
53 - rxd1-skew-ps : Skew control of RX data 1 pad
54 - rxd2-skew-ps : Skew control of RX data 2 pad
55 - rxd3-skew-ps : Skew control of RX data 3 pad
56 - txd0-skew-ps : Skew control of TX data 0 pad
57 - txd1-skew-ps : Skew control of TX data 1 pad
58 - txd2-skew-ps : Skew control of TX data 2 pad
59 - txd3-skew-ps : Skew control of TX data 3 pad
64 value is 0, and the maximum is property-dependent. The increment
65 step is 60ps. The default value is the neutral setting, so setting
66 rxc-skew-ps=<0> actually results in -900 picoseconds adjustment.
72 - rxc-skew-ps : Skew control of RX clock pad
73 - txc-skew-ps : Skew control of TX clock pad
77 - rxdv-skew-ps : Skew control of RX CTL pad
78 - txen-skew-ps : Skew control of TX CTL pad
79 - rxd0-skew-ps : Skew control of RX data 0 pad
80 - rxd1-skew-ps : Skew control of RX data 1 pad
81 - rxd2-skew-ps : Skew control of RX data 2 pad
82 - rxd3-skew-ps : Skew control of RX data 3 pad
83 - txd0-skew-ps : Skew control of TX data 0 pad
84 - txd1-skew-ps : Skew control of TX data 1 pad
85 - txd2-skew-ps : Skew control of TX data 2 pad
86 - txd3-skew-ps : Skew control of TX data 3 pad
88 - micrel,force-master:
98 step is 100ps. Unlike KSZ9031, the values represent picoseccond delays.
99 A negative value can be assigned as rxc-skew-psec = <(-100)>;.
103 Range of the value -700 to 2400, default value 0:
105 - rxc-skew-psec : Skew control of RX clock pad
106 - txc-skew-psec : Skew control of TX clock pad
108 Range of the value -700 to 800, default value 0:
110 - rxdv-skew-psec : Skew control of RX CTL pad
111 - txen-skew-psec : Skew control of TX CTL pad
112 - rxd0-skew-psec : Skew control of RX data 0 pad
113 - rxd1-skew-psec : Skew control of RX data 1 pad
114 - rxd2-skew-psec : Skew control of RX data 2 pad
115 - rxd3-skew-psec : Skew control of RX data 3 pad
116 - txd0-skew-psec : Skew control of TX data 0 pad
117 - txd1-skew-psec : Skew control of TX data 1 pad
118 - txd2-skew-psec : Skew control of TX data 2 pad
119 - txd3-skew-psec : Skew control of TX data 3 pad
124 phy0: ethernet-phy@0 {
125 rxc-skew-ps = <3000>;
126 rxdv-skew-ps = <0>;
127 txc-skew-ps = <3000>;
128 txen-skew-ps = <0>;
134 phy-mode = "rgmii-id";